Network Working Group                                         D. Sprague
Request for Comments: 3094                                    R. Benedyk
Category: Informational                                       D. Brendes
                                                               J. Keller
                                                                 Tekelec
                                                              April 2001


              Tekelec's Transport Adapter Layer Interface

Status of this Memo

   This memo provides information for the Internet community.  It does
   not specify an Internet standard of any kind.  Distribution of this
   memo is unlimited.

Copyright Notice

   Copyright (C) The Internet Society (2001).  All Rights Reserved.

IESG Note:

   Readers should note that this memo presents a vendor's alternative to
   standards track technology being developed by the IETF SIGTRAN
   Working Group.  The technology presented in this memo has not been
   reviewed by the IETF for its technical soundness or completeness.
   Potential users of this type of technology are urged to examine the
   SIGTRAN work before deciding to use the technology described here.

Abstract

   This document proposes the interfaces of a Signaling Gateway, which
   provides interworking between the Switched Circuit Network (SCN) and
   an IP network.  Since the Gateway is the central point of signaling
   information, not only does it provide transportation of signaling
   from one network to another, but it can also provide additional
   functions such as protocol translation, security screening, routing
   information, and seamless access to Intelligent Network (IN) services
   on both networks.

   The Transport Adapter Layer Interface (TALI) is the proposed
   interface, which provides TCAP (Transaction Capability Application
   Part), ISUP (ISDN User Part), and MTP (Mail Transport Protocol)
   messaging over TCP/IP.  In addition, TALI provides SCCP (Signalling
   Connection Control Part) Management (SCMG), MTP Primitives, dynamic
   registration of circuits, and routing of call control messages based
   on circuit location.




Sprague, et al.              Informational                      [Page 1]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


Table of Contents

   1. Introduction                                                    4
   2. Overview of the TALI Protocol                                   6
   2.1 Traditional PSTN SS7 Networks                                  6
   2.2 Converged SS7 Networks                                         8
   2.3 TALI Protocol Stack Overview                                  10
   2.3.1 An Alternate TALI Protocol Stack using the SAAL Layer       13
   2.3.2 An Alternate TALI Protocol Stack using SCTP                 15
   2.4 Inputs to the TALI Version 1.0 State Machine                  15
   3. TALI Version 1.0                                               17
   3.1 Overview of the TALI Message Structure                        17
   3.1.1 Types of TALI Fields                                        19
   3.2 Detailed TALI Message Structure                               20
   3.2.1 TALI Peer to Peer Messages                                  20
   3.2.1.1 Test Message (test)                                       20
   3.2.1.2 Allow Message (allo)                                      21
   3.2.1.3 Prohibit Message (proh)                                   21
   3.2.1.4 Prohibit Acknowledgement Message (proa)                   21
   3.2.1.5 Monitor Message (moni)                                    22
   3.2.1.6 Monitor Acknowledge Message (mona)                        22
   3.2.2 Service Messages                                            23
   3.2.2.1 SCCP Service Message (sccp)                               23
   3.2.2.1.1 SCCP Encapsulation using TALI                           25
   3.2.2.2 ISUP Service Message (isot)                               27
   3.2.2.2.1 ISUP Encapsulation using TALI                           27
   3.2.2.3 MTP3 Service Message (mtp3)                               28
   3.2.2.3.1 MTP3 Encapsulation using TALI                           29
   3.2.2.4 SAAL Service Message (saal)                               30
   3.2.2.4.1 MTP3 and SAAL Peer to Peer Encapsulation using TALI     31
   3.3 TALI Timers                                                   34
   3.3.1 T1 Timer                                                    34
   3.3.2 T2 Timer                                                    34
   3.3.3 T3 Timer                                                    34
   3.3.4 T4 Timer                                                    34
   3.3.5 Recommended Defaults and Ranges for the TALI Timers         35
   3.4 TALI User Events                                              35
   3.4.1 Management Open Socket Event                                35
   3.4.2 Management Close Socket Event                               36
   3.4.3 Management Allow Traffic Event                              36
   3.4.4 Management Prohibit Traffic Event                           36
   3.5 Other Implementation Dependent TALI Events                    37
   3.6 TALI States                                                   37
   3.7 TALI Version 1.0 State Machine                                38
   3.7.1 State Machine Concepts                                      38
   3.7.1.1 General Protocol Rules                                    38
   3.7.1.2 Graceful Shutdown of a Socket                             39
   3.7.1.3 TALI Protocol Violations                                  39



Sprague, et al.              Informational                      [Page 2]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   3.7.2 The State Machine                                           40
   3.8 TALI 1.0 Implementation Notes                                 42
   3.8.1 Failure on a TCP/IP Socket                                  42
   3.8.2 Congestion on a TCP/IP Socket                               43
   3.9 TALI 1.0 Limitations                                          43
   4. TALI Version 2.0                                               43
   4.1 Overview of TALI Version 2.0 Features                         45
   4.2 TALI Version Identification                                   47
   4.3 Backwards Compatibility                                       50
   4.3.1 Generating Protocol Violations based on Received Messages   53
   4.4 Overview of the TALI Message Structure                        55
   4.4.1 Types of TALI Fields                                        55
   4.5 Detailed TALI Message Structures for New 2.0 Opcodes          58
   4.5.1 Management Message (mgmt)                                   60
   4.5.1.1 Routing Key Registration Primitive (rkrp)                 61
   4.5.1.1.1 RKRP Data Structures                                    65
   4.5.1.1.1.1 Common Fields in all RKRP Messages                    65
   4.5.1.1.1.2 CIC Based Routing Key Operations                      67
   4.5.1.1.1.3 SCCP Routing Key Operations                           71
   4.5.1.1.1.4 DPC-SI, DPC and SI based Routing Key Operations       74
   4.5.1.1.1.5 Default Routing Key Operations                        76
   4.5.1.1.1.6 Support for Multiple RKRP Registration Operations     78
   4.5.1.1.1.6.1 Multiple Registrations Support                      78
   4.5.1.1.1.6.2 Multiple RKRP Operations in a Single Message        80
   4.5.1.2 MTP3 Primitive (mtpp)                                     82
   4.5.1.3 Socket Option Registration Primitive (sorp)               87
   4.5.2 Extended Service Message (xsrv)                             91
   4.5.3 Special Message (spcl)                                      92
   4.5.3.1 Special Messages Not Supported (smns)                     93
   4.5.3.2 Query Message (qury)                                      93
   4.5.3.3 Reply Message (rply)                                      94
   4.5.3.4 Unsolicited Information Message (USIM)                    95
   4.6 TALI Timers                                                   95
   4.7 TALI User Events                                              95
   4.8 TALI States                                                   96
   4.9 TALI Version 2.0 State Machine                                96
   4.9.1 State Machine Concepts                                      96
   4.9.1.1 General Protocol Rules                                    96
   4.9.1.2 Graceful Shutdown of a Socket                             97
   4.9.1.3 TALI Protocol Violations                                  97
   4.9.2 The State Machine                                           97
   4.10 TALI 2.0 Specification Limitations                          101
   5. Success/Failure Codes                                         101
   6. Security Considerations                                       102
   7. References                                                    102
   8. Acknowledgments                                               103
   9. Authors' Addresses                                            104
   10. Full Copyright Statement                                     105



Sprague, et al.              Informational                      [Page 3]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


1. Introduction

   This document is organized into the following 6 sections:

   -  Introduction to the document
   -  Overview of the TALI Protocol
   -  TALI Version 1.0
   -  TALI Version 2.0
   -  Success/Failure Codes
   -  Security Considerations

   The following terms are used throughout this document.

   Circuit Identification Code (CIC):
   A field identifying the circuit being setup or released.  Depending
   on SI and MSU Type, this field can be 12, 14 or 32 bits.

   Changeover/Changeback (co/cb):
   SS7 MTP3 procedure related to link failure and re-establishment.

   Far End (FE):
   The remote endpoint of a socket connection.

   Far End Allowed (FEA):
   The FE is ready to use the socket for service PDUs.

   Far End Prohibited (FEP):
   The FE is not ready to use the socket for service PDUs.

   Intelligent Network (IN):
   A network that allows functionality to be distributed flexibly at a
   variety of nodes on and off the network and allows the architecture
   to be modified to control the services.

   Management ATM Adaptation Layer (MAAL):
   This layer is a component of SAAL.  This layer maps requests and
   indications between the System Management for the SG and the other
   SAAL layers.  MAAL includes interfaces to/from SSCOP, SSCF, and
   system management.  More information can be found in T1.652.

   Media Gateway (MG):
   A MG terminates SCN media streams, packetizes the media data, if it
   is not already packetized, and delivers packetized traffic  to the
   packet network.  It performs these functions in reverse order for
   media streams flowing from the packet network to the SCN.






Sprague, et al.              Informational                      [Page 4]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   Media Gateway Controller (MGC):
   An MGC handles the registration and management of resources at the
   MG.  The MGC may have the ability to authorize resource usage based
   on local policy.  For signaling transport purposes, the MGC serves as
   a possible termination and origination point for SCN application
   protocols, such as SS7 ISDN User Part and Q.931/DSS1.

   MTP3 Framing (MTP3F):
   TALI does not require full MTP3 procedures support but rather uses
   the MTP3 framing structure (ie: SIO, Routing Label, etc)

   Near End (NE):
   The local endpoint of a socket connection.

   Near End Allowed (NEA):
   The NE is ready to use the socket for service PDUs.

   Near End Prohibited (NEP):
   The NE is not ready to use the socket for service PDUs.

   Q.BICC ISUP:
   An ISUP+ variant that uses 32 bit CIC codes instead of 14/12 bit CIC
   codes.  ISUP+, or Q.BICC ISUP, is based on the Q.765.BICC
   specification currently being developed in ITU Study Group 11.

   Signaling ATM Adaptation Layer (SAAL):
   This layer is the equivalent of MTP-2 for ATM High Speed Links
   carrying SS7 Traffic as described in GR-2878-CORE [8].  SAAL includes
   SSCF, SSCOP and MAAL.

   Signaling Gateway (SG):
   An SG is a signaling agent that receives/sends SCN native signaling
   at the edge of the IP network.  The SG function may relay, translate
   or terminate SS7 signaling in an SS7-Internet Gateway.  The SG
   function may also be co-resident with the MGC/MG functions to process
   SCN signaling associated with line or trunk terminations controlled
   by the MG (e.g., signaling backhaul).

   Service Specific Coordination Function (SSCF):
   This layer is a component of SAAL.  This layer maps the services
   provided by the lower layers of the SAAL to the needs of a specific
   higher layer user.  In the case of the STP, the higher layer user is
   the MTP-3 protocol, and the SSCF required is that as defined by
   T1.645: SSCF for Support of Signaling at the Network Node Interface
   (SSCF at the NNI).  More information can be found in T1.645.  SSCF
   provides the interface between SSCOP and MTP3 and includes the
   following functions:




Sprague, et al.              Informational                      [Page 5]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   -  Local Retrieve of messages to support link changeover procedures
   -  Flow control with four levels of congestion

   Switched Circuit Network (SCN):
   The term SCN is used to refer to a network that carries traffic
   within channelized bearers of pre-defined sizes.  Examples include
   Public Switched Telephone Networks (PSTNs) and Public Land Mobile
   Networks (PLMNs).  Examples of signaling protocols used in SCN
   include Q.931, SS7 MTP Level 3 and SS7 Application/User parts.

   Service Specific Connection Oriented Protocol (SSCOP):
   This layer is a component of SAAL.  This layer provides reliable
   point to point data transfer with sequence integrity and error
   recovery by selective retransmission.  Protocol layer interfaces are
   described in T1.637.  Aspects of the protocol include flow control,
   connection control, error reporting to layer management, connection
   maintenance in the prolonged absence of data transfer, local data
   retrieval by the user of the SSCOP, error detection of protocol
   control information and status reporting.  SSCOP provides the link
   layer functions that are:

   -  In-Sequence Delivery
   -  Flow Control
   -  Error Detection/Correction
   -  Keep Alive
   -  Local Data Retrieval
   -  Connection Control
   -  Protocol Error Detection and Recovery

   Signaling Transfer Point (STP):
   Packet switches that provide CCS message routing and transport.  They
   are stored programmed switches that use information contained in the
   message in conjunction with information stored in memory to route the
   message to the appropriate destination signaling point.

2. Overview of the TALI Protocol

2.1 Traditional PSTN SS7 Networks

   The traditional PSTN SS7 network consists of 3 types of devices
   connected via dedicated SS7 signaling links.

   The 3 primary device types for PSTN networks are:

   *  SSP:  Signaling Service Point.  These nodes act as endpoints in
      the SS7 network, originating SS7 messages as users attempt to
      place phone calls.  These nodes contain interfaces into the SS7
      data network and the SS7 voice network.



Sprague, et al.              Informational                      [Page 6]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   *  STP: Signaling Transfer Point.  These nodes act primarily as
      switches, switching SS7 traffic from node to node throughout the
      network until it reaches another endpoint.  An important feature
      of each STP is to provide SS7 network management functionality
      that allows messages to be delivered even when links and devices
      fail.  STPs also sometimes provide database type services, such as
      Global Title Translations and Local Number Portability.

   *  SCP: Signaling Control Point.  These nodes act as databases.
      These nodes contain stored data that is used to turn SS7 Queries
      into SS7 Replies.

   There are 3 primary types of dedicated SS7 signaling links:

   *  56Kbps SS7 (DS0, V35, OCU) links.  These links implement the MTP-1
      and MTP-2 protocols as defined in [1].

   *  DS1 High Speed Links.  These links use the SAAL protocol to
      provide an alternative to 56Kbps SS7 links that is based on newer,
      faster technology.  These links implement the SS7 protocol as
      defined in [8].

   *  E1 Links.

      Figure 1 provides an overview of the traditional PSTN network.  In
      this network, any of the links can be implemented via either 56
      Kbps, DS1, or E1 links.
























Sprague, et al.              Informational                      [Page 7]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


                                 ^
                                / \
                               /SCP\
                              /-----\
                                /  \
                               /    \
                              /      \
                             /        \
               /---\      +---+    +---+      /---\
              | SSP |-----|STP|----|STP|-----| SSP |
               \---/  \  /+-+-+\  /+-+-+ \  / \---/
                       \/   |   \/   |    \/
                       /\   |   /\   |    /\
               /---\  /  \+-+-+/  \+-+-+ /  \ /---\
              | SSP |/----|STP|----|STP|/----| SSP |
               \---/      +---+    +---+      \---/
                           \           /
                            \         /
                             \       /
                              \  ^  /
                               \/ \/
                               /SCP\
                              /-----\

              Figure 1: The Traditional PSTN Network

2.2 Converged SS7 Networks

   In the converged SS7 network, SS7 devices will reside on both the
   traditional PSTN network (with dedicated 56 Kbps and DS1 links) and
   on the IP network (with Ethernet links based on IP protocol).  The
   services of SSPs, STPs, and SCPs can be provided by new types of
   devices that reside on IP networks.  The IP network is not intended
   to completely replace the PSTN, rather devices on the 2 types of
   networks must be able to communicate with one another and convert
   from 1 lower layer protocol to the other.

   Signaling Gateways are new devices that may also function as an STP
   in the converged network.  SGs provide interfaces to:

   *  devices on the SCN (traditional SSPs, STPs, and SCPs)

   *  other SGs

   *  new devices on the IP network

   SGs also continue to perform STP functions such as SS7 network
   management and some database services (such as GTT and LNP).



Sprague, et al.              Informational                      [Page 8]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   New devices on the IP network include:

   *  Media Gateway Controllers.  In addition to other functions, these
      devices control Media Gateways and perform call processing.

   *  Media Gateways.  In addition to other functions, these devices
      control voice circuits that are used to carry telephone calls.
      MGs + MGCs combine to provide the functionality of traditional
      SSPs.

   *  IP based SCPs.  The database services that are related to SS7 can
      be moved onto devices on the IP network.

      Figure 2 provides an overview of the converged SS7 network.

                         -----              +----+
                /\      /     \-------------| SG |
               /  \----|  SCN  |     +----+ +----+
              /SCP \    \     /------| SG |  |
              ------     -----       +----+  |
                         |   |           |   |
                         |   |           |   |
                         |   |           -----
                         |   |          /     \      /\
                         |   |         |  IP   |----/  \
                         |  /---\       \     /    /SCP \
                         | | SSP |       -----     ------
                         |  \---/         /   \
                         |     |         /     \
                       /---\   |        /       \
                      | SSP |  |     +---+    +---+
                       \---/ +----+  |MGC|    |MGC|
                         |   | MG |  +---+    +---+
                         |   +----+\    \     /
                         |          \    \   /
                         |           \   -----
                         |            \ /     \
                       +----+          |  IP   |
                       | MG |-----------\     /
                       +----+            -----

                    Figure 2: The Converged SS7 Network

   In theory, the TALI protocol can be used between 2 nodes to carry SS7
   traffic across TCP/IP.  Some of the areas that TALI could be used
   include:





Sprague, et al.              Informational                      [Page 9]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   -  For SG to SG communication across IP
   -  For SG to MGC communication across IP
   -  For SG to IP based SCP communication across IP
   -  For communication between multiple IP based SCPs
   -  For communication between multiple MGCs
   -  For communication between MGCs and MGs
   -  For other IP devices such as DNS, Policy Servers, etc.

   In reality, the communication between MGCs, or between MGC and MG is
   probably better suited to using other protocols.  With respect to the
   Signaling Gateway implementation, the TALI protocol is used to carry
   SS7 traffic:

   -  For SG to SG communication
   -  For SG to MGC communication
   -  For SG to IP based SCP communication

2.3 TALI Protocol Stack Overview

   The Transport Adapter Layer Interface is the proposed interface that
   provides SCCP, ISUP, and MTP messaging encapsulation within a TCP/IP
   packet between two switching elements.  In addition, TALI provides
   SCCP Management (SCMG), MTP Primitives, dynamic registration of
   circuits, and routing of call control messages based on circuit
   location.

   The major purpose of the TALI protocol is to provide a bridge between
   the SS7 Signaling Network and applications that reside within an IP
   network.  Figure 3 provides a simple illustration that highlights the
   protocol stacks used for transport of SS7 MSUs on both the SS7 side
   and the IP side of the SG.




















Sprague, et al.              Informational                     [Page 10]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


                 SS7 traffic       SS7 traffic
              via 56Kbps links     via TALI
       +-----------+        +----+          +--------+
       |Traditional|        | SG |          |   IP   |
       |SS7 Devices|<------>|    |<-------->| Devices|
       +-----------+        +----+          +--------+


          SS7                          SS7, TALI, TCP/IP
          protocol stack               protocol stack
        +---------------+              +---------------+
        |SS7 application|              |SS7 application|
        |layer          |              |layer          |
        +-------+-------+              +-------+-------+
        | TCAP  | ISUP  |              | TCAP  | ISUP  |
        +-------+       |              +-------+       |
        | SCCP  |       |              | SCCP  |       |
        +-------+-------+              +-------+-------+
        |    MTP3       |              |    MTP3       |
        +---------------+              +---------------+
        |    MTP2       |              |    TALI       |
        +---------------+              +---------------+
        |    MTP1       |              |    TCP        |
        |   (& phy.     |              +---------------+
        |    layer)     |              |    IP         |
        +---------------+              +---------------+
                                       |    MAC        |
                                       |   (& phy.     |
                                       |    layer)     |
                                       +---------------+

       Figure 3: TALI Protocol to carry SS7 over TCP/IP

   From Figure 3, several observations can be made:

   *  The TALI layer is used when transferring SS7 over IP.

   *  When SS7 traffic is carried over a IP network, the MTP2 and MTP1
      layers of a traditional 56 Kbps link are replaced by the TALI,
      TCP, IP, and MAC layers

   *  The TALI layer sits on top of the TCP layer.

   *  The TALI layer sits below the various SS7 layers (MTP3, SCCP/TCAP,
      ISUP, and applications).  The data from these SS7 layers is
      carried as the data portion of TALI service data packets.





Sprague, et al.              Informational                     [Page 11]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   Some of the facts concerning the TALI protocol which are important to
   understanding how TALI works that are not evident from Figure 3
   include the following:

   *  Each TALI connection is provided over a single TCP socket.

      *  The standard Berkeley sockets interface to the TCP is used by
         the TALI layer to provide connection oriented service from
         endpoint to peer endpoint.

      *  TCP sockets are based on a Client/Server architecture; one end
         of the TALI connection must be defined as the 'server side',
         the other end is a 'client'.

      *  The client/server roles are important only in bringing up the
         TCP connection between the 2 endpoint, once the connection is
         established both ends use the same Berkeley sockets calls
         (send, recv) to transfer data.

      *  The TCP socket must be connected before the 2 TALI endpoints
         can begin communicating.

   *  TALI provides user control over each TALI connection that is
      defined.  This control:

      *  Allows the user to control when each TALI connection will be
         made

      *  Allows the user to control when each TALI connection is allowed
         to carry SS7 traffic

      * Allows the user to control the graceful shutdown of each socket

   *  TALI provides Peer to Peer messages.  These messages originate
      from the TALI layer of one endpoint of the connection and are
      terminated at the TALI layer of the other endpoint.  Peer to Peer
      messages are used:

      *  To provide test and watchdog maintenance messages

      *  To control the ability of each socket to carry SS7 service
         messages

   *  TALI provides Service messages.  These messages originate from the
      layer above the TALI layer of one endpoint of the connection and
      are transferred to and terminated at the layer above the TALI
      layer of the other endpoint.




Sprague, et al.              Informational                     [Page 12]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


      *  The service messages provide several different ways to
         encapsulate the SS7 messages (SCCP/TCAP, ISUP, and other MTP3
         layer data) across the TCP/IP connection.

      *  As we will see later, different Service opcodes are used to
         communicate across the TALI socket exactly how each SS7 message
         has been encapsulated.

   *  A set of TALI timers is defined.  These timers are used to
      correctly implement the TALI state machine.

2.3.1 An Alternate TALI Protocol Stack using the SAAL Layer

   This section presents a different, slightly more complex, TALI
   protocol stack that can be used in place of the protocol stack in the
   previous section.

   Figure 3 in the previous section provided a simple illustration that
   highlighted the basic TALI protocol stack that can be used to
   transport SS7 MSUs between 56 Kbps links on the SS7 side of an SG and
   the IP devices.

   Figure 4 below illustrates an alternate TALI protocol stack that
   includes the SAAL layer as part of the data transferred across the
   TCP/IP connection.


























Sprague, et al.              Informational                     [Page 13]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


                    SS7 traffic       SS7 traffic
                    via DS1 links     via TALI
          +-----------+        +----+          +--------+
          |Traditional|        | SG |          |   IP   |
          |SS7 Devices|<------>|    |<-------->| Devices|
          +-----------+        +----+          +--------+


             SS7 DS1                   SS7, TALI, TCP/IP
             protocol stack            protocol stack
           +-----------------+        +-----------------+
           | SS7 application |        | SS7 application |
           | layer           |        | layer           |
           +--------+--------+        +--------+--------+
           |  TCAP  | ISUP   |        |  TCAP  | ISUP   |
           +--------+        |        +--------+        |
           |  SCCP  |        |        |  SCCP  |        |
           +--------+--------+        +--------+--------+
           |      MTP3       |        |      MTP3       |
           +-----------------+        +-----------------+
           |    SAAL         |        |     SAAL        |
           |(SSCF,MAAL,SSCOP)|        |(SSCF,MAAL,SSCOP)|
           +-----------------+        +-----------------+
           |     AAL5        |        |     TALI        |
           +-----------------+        +-----------------+
           |     ATM         |        |     TCP         |
           |    (& phy.      |        +-----------------+
           |     layer)      |        |     IP          |
           +-----------------+        +-----------------+
                                      |     MAC         |
                                      |    (& phy.      |
                                      |     layer)      |
                                      +-----------------+

        Figure 4: An Alternate TALI Protocol Stack with SAAL

   The following bullets provide a discussion regarding the differences
   between these 2 protocol stacks, the reasons for having 2 protocol
   stacks, and the advantages of each:

   *  When the TALI protocol stack is implemented without the SAAL
      layer, as in Figure 3, the SEQUENCE NUMBER of the SS7 MSU is NOT
      part of the data transferred across the TCP/IP connection.  In 56
      Kbps SS7 links, the MTP2 header contains an 8 bit sequence number
      for each MSU.  The sequence number is used to preserve message
      sequencing and to support complex SS7 procedures involving MSU
      retrieval during link changeover and changeback.  As indicated in
      Figure 3, the MTP2 header is NOT part of the data transferred



Sprague, et al.              Informational                     [Page 14]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


      across the TCP/IP connection.  The TALI protocol stack without
      SAAL still guarantees correct sequencing of SS7 data (this
      sequencing is provided by sequence numbers in the TCP layer),
      however that protocol stack can not support SS7 changeover and
      changeback procedures.

   *  When the TALI protocol stack is implemented with the SAAL layer,
      as in Figure 4, the SEQUENCE NUMBER of the SS7 MSU IS part of the
      data transferred across TCP/IP.  In SS7 DS1 links, the SSCOP
      trailer contains a 24 bit sequence number for each MSU.  This 24
      bit sequence number serves the same purposes as the 8 bit SS7
      sequence number.  As indicated in Figure 4, the SSCOP trailer IS
      part of the data transferred across the TCP/IP connection.  The
      protocol stack in Figure 4 can support SS7 changeover and
      changeback procedures.

   *  Implementing the TALI protocol with SAAL therefore provides
      support for SS7 co/cb and data retrieval and can help to minimize
      MSU loss as SS7 links are deactivated.  However, implementing SAAL
      is not a trivial matter.  The SAAL layer consists of 3 sublayers
      (SSCF, SSCOP, and MAAL), one of which (SSCOP) is quite involved.
      It is envisioned that most SS7 to TCP/IP applications will NOT
      choose to implement SAAL.

2.3.2 An Alternate TALI Protocol Stack using SCTP

   The TALI protocol is dependent on a reliable transport layer below
   it.  At the initial design of TALI, TCP was the only reliable, proven
   transport layer.  Simple Control Transport Protocol (SCTP) is
   currently being designed as a transport later specifically for
   signalling.  Once SCTP is a proven and accepted transport protocol,
   SCTP can then be used in place of TCP as shown in Figures 3 and 4.

2.4 Inputs to the TALI Version 1.0 State Machine

   Figure 5 illustrates the inputs that affect the TALI State Machine.
   Inputs to the state machine include:

   *  Management events (ie: requests from the human user of the TALI
      connection) to control the operation of a particular TALI session.

   *  TALI messages received from the Peer.  These messages include peer
      to peer messages as well as service data messages.

   *  Events from the User of the TALI layer.  The user is the layer
      above TALI in the protocol stack, either the SS7 or SAAL layer.





Sprague, et al.              Informational                     [Page 15]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   *  Implementation Dependent Events.  Each implementation must provide
      inputs into the TALI state machine such as:

      *  Socket Events

      *  TALI protocol violations.  The TALI state machine must detect
         protocol violations and act accordingly.

      * Timer events.










































Sprague, et al.              Informational                     [Page 16]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


      +====+                                   +============+
      |    |    +---------+ +-------------+    |            |
      |User|    | Service | | Mgmt. Open  |    | MANAGEMENT |
      |Part|<-->| Message | | Mgmt. Close |<-->|            |
      |    |    |         | | Mgmt. Proh. |    |            |
      |    |    +---------+ | Mgmt. Allow |    +============+
      +====+          ^     +-------------+
                      |            ^
                      |            |
                      v            v
      +========================================================+
      |                 TALI State Machine                     |
      +========================================================+
            ^               ^                 ^             ^
            |               |                 |             |
            |               |                 |             |
            v               |                 |             |
       +---------+  +-----------------+ +-----------+ +------------+
       | Received|  | Connection est. | | Protocol  | | T1 Expired |
       | 'test'  |  | Connection lost | | Violation | | T2 Expired |
       | 'allo'  |  |                 | |           | | T3 Expired |
       | 'proh'  |  +-----------------+ +-----------+ | T4 Expired |
       | 'proa'  |          ^                 ^       +------------+
       | 'moni'  |          |                 |              ^
       | 'mona'  |          |                 |              |
       |    or   |          |                 |              |
       | Service |          |                 |              |
       | Message |    +========================================+
       +---------+    |         IMPLEMENTATION                 |
            ^         |           DEPENDENT                    |
            |         +========================================+
            |
            v
        +============+
        |    PEER    |
        |            |
        +============+

      Figure 5: Overview of Inputs to the TALI 1.0 State Machine












Sprague, et al.              Informational                     [Page 17]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


3. TALI Version 1.0

   This chapter provides the states, messages, message exchange rules
   and state machine that must be implemented to provide a TALI version
   1.0 protocol layer.

3.1 Overview of the TALI Message Structure

   Table 2 provides a summary of the messages and message structure used
   in TALI version 1.0.

   +------------------------------------------------------------------+
   | OCTET | DESCRIPTION              | SIZE     | VALUE  |    TYPE   |
   +------------------------------------------------------------------+
   | 0..3  | SYNC                     | 4 Octets |        | 4 byte    |
   |       |                          |          |        | ASCII     |
   +------------------------------------------------------------------+
   |       |   TALI                   |          | 'TALI' |           |
   +------------------------------------------------------------------+
   | 4..7  | OPCODE                   | 4 Octets |        | 4 byte    |
   |       |                          |          |        | ASCII     |
   +------------------------------------------------------------------+
   |       |   Test Service           |          | 'test' |           |
   |       |   Allow Service          |          | 'allo' |           |
   |       |   Prohibit Service       |          | 'proh' |           |
   |       |   Prohibit Service Ack   |          | 'proa' |           |
   |       |   Monitor Socket         |          | 'moni' |           |
   |       |   Monitor Socket Ack     |          | 'mona' |           |
   |       |   SCCP Service           |          | 'sccp' |           |
   |       |   ISUP Service over TALI |          | 'isot' |           |
   |       |   MTP3 Service over TALI |          | 'mtp3' |           |
   |       |   Service over SAAL      |          | 'saal' |           |
   +------------------------------------------------------------------+
   | 8..9  | LENGTH                   | 2 Octets |        | integer   |
   |       |   (least significant     |          |        |           |
   |       |    byte first) non-0     |          |        |           |
   |       |    if Service or         |          |        |           |
   |       |    Socket monitor message|          |        |           |
   +------------------------------------------------------------------+
   | 10..X | DATA PAYLOAD             | variable |        | variable  |
   +------------------------------------------------------------------+

                 Table 2: Message Structure for TALI 1.0

   Table 3 indicates the valid values of the LENGTH field for each
   version 1.0 opcode.  The LENGTH field is always an indication of the
   # of bytes contained in the DATA PAYLOAD portion of a general TALI
   message.



Sprague, et al.              Informational                     [Page 18]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   +------------------------------------------------------------------+
   | OPCODE | VALID LENGTH VALUES | COMMENTS                          |
   +------------------------------------------------------------------+
   | test   | 0 bytes             |                                   |
   +------------------------------------------------------------------+
   | allo   | 0 bytes             |                                   |
   +------------------------------------------------------------------+
   | proh   | 0 bytes             |                                   |
   +------------------------------------------------------------------+
   | proa   | 0 bytes             |                                   |
   +------------------------------------------------------------------+
   | moni   | 0-200 bytes         | A maximum length is provided so   |
   |        |                     | that the maximum ethernet frame   |
   |        |                     | size is not exceeded.             |
   +------------------------------------------------------------------+
   | mona   | 0-200 bytes         | Mona reply length and content must|
   |        |                     | match the original moni (with the |
   |        |                     | exception of the opcode)          |
   +------------------------------------------------------------------+
   | sccp   | 12-265 bytes        | These are the valid sizes for the |
   |        |                     | SCCP-ONLY portions of SCCP UDT    |
   |        |                     | MSUs                              |
   +------------------------------------------------------------------+
   | isot   | 8-273 bytes         | The length is the number of octets|
   |        |                     | in the MTP3 and higher layer(s) of|
   |        |                     | the SS7 MSU.  This length includes|
   |        |                     | the SIO byte, the MTP3 routing    |
   |        |                     | label, the CIC code, and the      |
   |        |                     | ISUP Message Type field, and any  |
   |        |                     | other bytes that may exist as part|
   |        |                     | of the SIF (Service Information   |
   |        |                     | Field)                            |
   +------------------------------------------------------------------+
   | mtp3   | 5-280 bytes         | The length is the number of octets|
   |        |                     | in the MTP3 and higher layer(s) of|
   |        |                     | the SS7 MSU.  This length includes|
   |        |                     | the SIO byte and the MTP3 routing |
   |        |                     | labeld, and any other bytes that  |
   |        |                     | may exist as part of the SIF      |
   |        |                     | (Service Information Field)       |
   +------------------------------------------------------------------+
   | saal   | 11-280 bytes        | The length is the number of octets|
   |        |                     | in the MTP3 and higher layer(s) of|
   |        |                     | the SS7 MSU.  This length includes|
   |        |                     | the SIO byte and all bytes in the |
   |        |                     | SIF (Service Information Field)   |
   |        |                     | field.  The MTP3 routing label is |
   |        |                     | part of the SIF field.  Seven (7) |



Sprague, et al.              Informational                     [Page 19]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   |        |                     | octets of SSCOP trailer is added  |
   |        |                     | to the message.  The SSCOP trailer|
   |        |                     | bytes are also included in the    |
   |        |                     | length.                           |
   +------------------------------------------------------------------+

        Table 3: Valid Length Fields for Each Opcode in TALI 1.0

3.1.1 Types of TALI Fields

   Several field types are used in the general TALI message structure.

   +------------------------------------------------------------------+
   |Field Type | Implementation Notes for that Type                   |
   +------------------------------------------------------------------+
   |4 byte     | * 4 byte ASCII text strings are used to define the   |
   |ASCII text |   sync code and the opcode of the basic TALI message.|
   |           | * These fields are case sensitive, the coding for    |
   |           |   each sync and opcode literal needs to match the    |
   |           |   case specified in Table 2.                         |
   |           | * The standard ASCII conversion table is used to     |
   |           |   transform each character into a byte.              |
   |           | * The order of the ASCII characters is important.    |
   |           |   The first character in the string must be the      |
   |           |   first character transmitted across the wire.       |
   |           | * For example, if the string being encoded is 'abCD',|
   |           |   the order of the bytes as they are transferred     |
   |           |   over the wire must be:                             |
   |           |     1st byte: 0x61 ('a')  3rd byte: 0x43 ('C')       |
   |           |     2nd byte: 0x62 ('b')  4th byte: 0x44 ('D')       |
   |           | * The software for each implementation should be     |
   |           |   written in a manner that accounts for the required |
   |           |   byte order of transmission (ie: the Big Endian/    |
   |           |   Little Endian characteristics of the processor     |
   |           |   need to be dealt with in the software.             |
   +------------------------------------------------------------------+
   |Integer    | * A 1, 2 or 4 byte field to be treated as an integer |
   |           |   value.  Integer fields should be transmitted Least |
   |           |   Significant Byte first across the wire.            |
   |           | * The software for each implementation should be     |
   |           |   written in a manner that accounts for the required |
   |           |   byte order of transmission (ie: the Big Endian/    |
   |           |   Little Endian characteristics of the processor     |
   |           |   need to be dealt with in the software.             |
   +------------------------------------------------------------------+
   |Variable   | * The definition of the message structure for this   |
   |           |   field is governed by other specifications.         |
   |           | * For example, when transferring MTP3 service data   |



Sprague, et al.              Informational                     [Page 20]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   |           |   via a 'mtp3' opcode, the DATA PAYLOAD begins with  |
   |           |   the SIO byte of the MTP3 routing label.  The       |
   |           |   structure for the entire DATA PAYLOAD is governed  |
   |           |   by the MTP3 message structure defined in [1].      |
   +------------------------------------------------------------------+
   |X byte     | * ASCII text fields of sizes other than 4 bytes      |
   |ASCII text |   should be supported according to the same rules    |
   |           |   presented for the 4 byte ASCII text fields.  For   |
   |           |   instance, an 8 byte string such as 'ab01cd23' could|
   |           |   be used, where the 'a' would be the first byte of  |
   |           |   the field transmitted out the wire.                |
   +------------------------------------------------------------------+

         Table 4: Implementation Notes for each Type of TALI field

3.2 Detailed TALI Message Structure

3.2.1 TALI Peer to Peer Messages

   The following subsections provide more information regarding the TALI
   Peer to Peer messages that are implemented in version 1.0.  The TALI
   peer to peer messages originate at the TALI layer of 1 end of the
   socket connection (the near end) and are terminated at the TALI layer
   of the far end of the connection.

3.2.1.1 Test Message (test)

   The 'test' message is used by a TALI implementation to query the
   remote end of the TALI connection with respect to the willingness of
   the remote end to carry SS7 service data.  This message asks the
   other end: are you ready to carry service data?  This message is sent
   periodically by each TALI implementation based on a T1 timer
   interval.  Upon receiving 'test', a TALI implementation must reply
   with either 'proh' or 'allo' to indicate the nodes willingness to
   carry SS7 service data over that TALI connection.

   +------------------------------------------------------------------+
   | Octets | Field Name  | Description                               |
   +------------------------------------------------------------------+
   | 0..3   | SYNC        | 'TALI'                                    |
   +------------------------------------------------------------------+
   | 4..7   | OPCODE      | 'test'                                    |
   +------------------------------------------------------------------+
   | 8..9   | LENGTH      | Length = 0                                |
   +------------------------------------------------------------------+






Sprague, et al.              Informational                     [Page 21]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


3.2.1.2 Allow Message (allo)

   The 'allo' message is sent in reply to a 'test' query, or in response
   to some internal implementation event, to indicate that a TALI
   implementation IS willing to carry SS7 service data over the TALI
   session.  This message informs the far end that SS7 traffic can be
   transmitted on the socket.  'allo' is one of the 2 possible replies
   to a 'test' message.  Before SS7 traffic can be carried over a
   socket, both ends of the connection need to send 'allo' messages.

   +------------------------------------------------------------------+
   | Octets | Field Name  | Description                               |
   +------------------------------------------------------------------+
   | 0..3   | SYNC        | 'TALI'                                    |
   +------------------------------------------------------------------+
   | 4..7   | OPCODE      | 'allo'                                    |
   +------------------------------------------------------------------+
   | 8..9   | LENGTH      | Length = 0                                |
   +------------------------------------------------------------------+

3.2.1.3 Prohibit Message (proh)

   The 'proh' message is sent in reply to a 'test' query, or in response
   to some internal implementation event, to indicate that a TALI
   implementation is NOT willing to carry SS7 service data over the TALI
   session.  This message informs the far end that SS7 traffic can not
   be transmitted on the socket.  'proh' is one of the 2 possible
   replies to a 'test' message.  As long as 1 end of the connection
   remains in the 'prohibited' state, SS7 traffic can not be carried
   over the socket.

   +------------------------------------------------------------------+
   | Octets | Field Name  | Description                               |
   +------------------------------------------------------------------+
   | 0..3   | SYNC        | 'TALI'                                    |
   +------------------------------------------------------------------+
   | 4..7   | OPCODE      | 'proh'                                    |
   +------------------------------------------------------------------+
   | 8..9   | LENGTH      | Length = 0                                |
   +------------------------------------------------------------------+

3.2.1.4 Prohibit Acknowledgement Message (proa)

   The 'proa' message is sent by a TALI implementation each time a
   'proh' is received from the far end.  This message is sent to
   indicate to the far end that his 'prohibit' message was received
   correctly and will be acted on accordingly.




Sprague, et al.              Informational                     [Page 22]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   +------------------------------------------------------------------+
   | Octets | Field Name  | Description                               |
   +------------------------------------------------------------------+
   | 0..3   | SYNC        | 'TALI'                                    |
   +------------------------------------------------------------------+
   | 4..7   | OPCODE      | 'proa'                                    |
   +------------------------------------------------------------------+
   | 8..9   | LENGTH      | Length = 0                                |
   +------------------------------------------------------------------+

3.2.1.5 Monitor Message (moni)

   The 'moni' message provides a generic ECHO capability that can be
   used by each TALI implementation as that implementation sees fit.  A
   TALI version 1.0 implementation does not have to originate a 'moni'
   message to be compliant with the 1.0 specification.  The primary
   intent of this message is to provide a way for the TALI layer to test
   the round-trip message transfer time on a socket.  A 'mona' message
   must be sent in reply to each received 'moni' message.  The DATA
   portion of a 'moni' message is vendor implementation dependent.  The
   DATA portion of each 'mona' reply must exactly match the DATA portion
   of the 'moni' that is replied to.  Regardless of whether an
   implementation chooses to send 'moni' or not, 'mona' must be sent in
   response to each 'moni' in order to remain compliant with the TALI
   protocol.

   +------------------------------------------------------------------+
   | Octets | Field Name  | Description                               |
   +------------------------------------------------------------------+
   | 0..3   | SYNC        | 'TALI'                                    |
   +------------------------------------------------------------------+
   | 4..7   | OPCODE      | 'moni'                                    |
   +------------------------------------------------------------------+
   | 8..9   | LENGTH      | Length                                    |
   +------------------------------------------------------------------+
   | 10..X  | DATA PAYLOAD| Vendor Dependent                          |
   +------------------------------------------------------------------+

3.2.1.6 Monitor Acknowledge Message (mona)

   As mentioned above, the 'mona' must be sent in reply to each received
   'moni'.  The contents of the 'mona' DATA area must match the DATA
   area of the received 'moni' message.








Sprague, et al.              Informational                     [Page 23]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   +------------------------------------------------------------------+
   | Octets | Field Name  | Description                               |
   +------------------------------------------------------------------+
   | 0..3   | SYNC        | 'TALI'                                    |
   +------------------------------------------------------------------+
   | 4..7   | OPCODE      | 'mona'                                    |
   +------------------------------------------------------------------+
   | 8..9   | LENGTH      | Length                                    |
   +------------------------------------------------------------------+
   | 10..X  | DATA PAYLOAD| Vendor Dependent                          |
   +------------------------------------------------------------------+

3.2.2 Service Messages

   The following subsections provide more information regarding the TALI
   Service messages that are implemented in version 1.0.  TALI Service
   messages are used to carry SS7 MSUs across the IP network.  The
   information in this section includes details with respect to how to
   encapsulate SS7 MSUs into TCP/IP frames using each of the TALI
   service opcodes.  The TALI service messages originate at the layer
   above TALI, are transported across the IP network via a TALI service
   message, and are delivered to the layer above TALI at the far end of
   the TALI connection.

3.2.2.1 SCCP Service Message (sccp)

   The 'sccp' opcode is used to deliver SS7 MSUs with a Service
   Indicator of 3 (SCCP) over a TALI connection.  This opcode is only
   used on TALI protocol stacks that are implemented without SAAL.  The
   MTP3 layer of the SS7 MSU is NOT part of the data transferred across
   TCP/IP for this opcode; the data portion of the TALI 'sccp' message
   begins with the first byte of the SCCP data area in the SS7 MSU
   (after the MTP3 routing label).  The first byte in the SCCP data area
   is an SCCP message type field.

   Several restrictions on the SCCP messages that this TALI opcode can
   carry exist.  These restrictions are as follows:

   *  SCCP messages contain an SCCP message type field.  The SCCP
      messages that are supported by TALI 1.0 implementations are
      limited to Class 0 and Class 1 SCCP messages with a message type
      field of either:

      *  UDT
      *  UDTS
      *  XUDT
      *  XUDTS




Sprague, et al.              Informational                     [Page 24]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   *  SCCP messages must contain a Point Code in the 'calling party'
      area in order to be transferred across the TCP/IP connection as a
      'sccp' message.  An implementation may choose to modify the
      original SCCP MSU to add an appropriate calling party point code
      before transmission across TALI if desired.

   *  SCCP messages must contain a Point Code in the 'called party' area
      in order to be transferred across the TCP/IP connection as a
      'sccp' message.  An implementation may choose to modify the
      original SCCP MSU to add an appropriate called party point code
      before transmission across TALI if desired.

   *  The encoding of the SS7 SCCP MSUs, as they are transmitted across
      TALI via 'sccp', should remain compliant with the ANSI
      specifications (T1.112 and T1.114) that apply to the SCCP and TCAP
      portions of the message respectively.

   NOTE 1: SCCP Subsystem Management for the IP based SCP's is supported
   via this 'sccp' opcode.  SS7 SCCP Management messages are controlled
   by an SCMG SS7 process.  SCMG sends the management messages via SCCP
   UNITDATA (UDT) messages.  Therefore, the SCMG messages can be sent
   across the TALI connection.

   NOTE 2: 'sccp' TALI messages will not include the MTP3 header and
   therefore will not retain the original DPC/OPC of the SS7 MSU.  Each
   TALI implementation needs to consider if/how to provide this DPC/OPC
   information in the SCCP portion of the message.  For example the DPC
   can be replicated to the point code in the SCCP Called Party Address
   area and the OPC can be replicated to the point code in the SCCP
   Calling Party Address area.

   +------------------------------------------------------------------+
   | Octets | Field Name  | Description                               |
   +------------------------------------------------------------------+
   | 0..3   | SYNC        | 'TALI'                                    |
   +------------------------------------------------------------------+
   | 4..7   | OPCODE      | 'sccp'                                    |
   +------------------------------------------------------------------+
   | 8..9   | LENGTH      | Length                                    |
   +------------------------------------------------------------------+
   | 10..X  | SCCP Data   | SCCP data starting at the first byte after|
   |        |             | the Layer 3 Routing Label (data does not  |
   |        |             | include the SIO or Routing Label)         |
   +------------------------------------------------------------------+







Sprague, et al.              Informational                     [Page 25]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


3.2.2.1.1 SCCP Encapsulation using TALI

   When an SCCP MSU arrives at an SG from a 56 Kbps or DS1 link and is
   routed within the SG for transmission to an IP device, the SG
   performs the following processing on the SS7 MSU:

   *  discards the MTP Layer 2 information, CRC and flags

   *  places the DPC from MTP Layer 3 into the Called Party Address
      field of the SCCP layer; the Calling Party Address field is
      created if it does not exist and then filled

   *  places the OPC from MTP Layer 3 into the Calling Party Address
      field of the SCCP layer if there is no Calling Party Point Code

   *  places the modified SCCP and unchanged TCAP data in the service
      payload area of the TALI packet

   *  The SYNC field is set

   *  The OPCODE is set to 'sccp'

   * The LENGTH is set to the number of octets in the SERVICE field

   Once the fully formed 'sccp' TALI packet is created, it is handed to
   the TCP socket layer and transmitted.  The transmission process will
   add TCP, IP and MAC header information.

   Since the routing information from MTP Layer 3 is placed in the SCCP
   part of the outgoing message, no routing information needs to be
   saved by the SG.




















Sprague, et al.              Informational                     [Page 26]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


                                SS7 MSU

           |          Layer 3          |     Layer 2      |
           |                           |                  |
      +----+---+-----+-----+-------+---+--+---+---+---+---+----+
      |Flag|FCS|TCAP |SCCP |Routing|SIO|LI|FIB|FSN|BIB|BSN|Flag|
      |    |   |Layer|Layer| Label |   |  |   |   |   |   |    |
      +----+---+-----+-----+-------+---+--+---+---+---+---+----+
               |           |
               |           |
               |           |
        TALI   +-----------+---+------+----+
        Packet |  Service  |LEN|Opcode|SYNC|
               +-----------+---+------+----+
               |                           |
               |                           |
               |                           |
               +---------------------------+------+------+------+
        IP     | TALI Packet               |TCP   | IP   | MAC  |
        Packet |                           |Header|Header|Header|
               +---------------------------+------+------+------+

   Figure 6: Encapsulation of SCCP MSUs using the TALI 'sccp' opcode

   When an 'sccp' TALI packet is received on by an SG from an IP device,
   the SG performs the following processing on the 'sccp' packet:

   *  validates the TALI header

   *  Allocates space for a new SS7 message

   *  Regenerates the SIO with the Sub-Service Field set to National
      Network, priority of zero (0), Service Indicator set to SCCP

   *  extracts the SCCP/TCAP data from the SERVICE area and places it in
      the new SS7 message

   *  sets the DPC to the SCCP Called Party Point Code

   *  sets the OPC to the SCCP Calling Party Point Code

   *  randomly generates the SLS

   Once the 'sccp' packet is transformed back into a normal SS7 MSU, the
   MSU is routed within the SG according to the normal SS7 routing
   procedures.





Sprague, et al.              Informational                     [Page 27]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


3.2.2.2 ISUP Service Message (isot)

   The 'isot' opcode is used to deliver SS7 MSUs with a Service
   Indicator of 5 (ISUP) over a TALI connection.  This opcode is only
   used on TALI protocol stacks that are implemented without SAAL.  The
   MTP3 layer of the SS7 MSU IS part of the data transferred across
   TCP/IP for this opcode; the data portion of the TALI 'isot' message
   begins with the SIO byte of the MTP3 header in the SS7 MSU.

   +------------------------------------------------------------------+
   | Octets | Field Name  | Description                               |
   +------------------------------------------------------------------+
   | 0..3   | SYNC        | 'TALI'                                    |
   +------------------------------------------------------------------+
   | 4..7   | OPCODE      | 'isot'                                    |
   +------------------------------------------------------------------+
   | 8..9   | LENGTH      | Length                                    |
   +------------------------------------------------------------------+
   | 10..X  | ISUP Data   | Raw ISUP data starting at the Layer 3 SIO |
   |        |             | field.                                    |
   +------------------------------------------------------------------+

3.2.2.2.1 ISUP Encapsulation using TALI

   When an ISUP MSU arrives at an SG from a 56 Kbps or DS1 link and is
   routed within the SG to a IP device, the SG performs the following
   processing on the SS7 MSU:

   *  discards the MTP Layer 2 information, CRC and flags

   *  places MTP Layer 3 into the SERVICE payload area of the TALI
      packet

   *  The SYNC field is set

   *  The OPCODE is set to 'isot'

   *  The LENGTH is set to the number of octets in the SERVICE field

   Once the fully formed 'isot' TALI packet is created, it is handed to
   the TCP socket layer and transmitted.  The transmission process will
   add TCP, IP and MAC header information.

   Since the routing information is placed in the TALI Packet, no
   routing information needs to be saved by the SG.






Sprague, et al.              Informational                     [Page 28]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


                              SS7 MSU

           |          Layer 3            |     Layer 2      |
           |                             |                  |
      +----+---+----+----+---+-------+---+--+---+---+---+---+----+
      |Flag|FCS|ISUP|Msg.|CIC|Routing|SIO|LI|FIB|FSN|BIB|BSN|Flag|
      |    |   |Part|Type|   |Label  |   |  |   |   |   |   |    |
      +----+---+----+----+---+-------+---+--+---+---+---+---+----+
               |                         /
               |                        /
               |                       |
        TALI   +-----------------------+---+------+----+
        Packet |  Service              |LEN|Opcode|SYNC|
               +-----------------------+---+------+----+
               |                                       /
               |                              ---------
               |                             /
               +----------------------------+------+------+------+
        IP     | TALI Packet                |TCP   | IP   | MAC  |
        Packet |                            |Header|Header|Header|
               +----------------------------+------+------+------+

     Figure 7: Encapsulation of ISUP MSUs using the TALI 'isot' opcode

   When an 'isot' TALI packet is received on an SG from an IP device,
   the SG performs the following processing on the 'isot' packet:

   *  validates the TALI header

   *  Allocates space for a new SS7 message

   *  extracts the MTP Layer 3 data from the SERVICE area and places it
      in the new SS7 message

   Once the 'isot' packet is transformed back into a normal SS7 MSU, the
   MSU is routed within the SG according to the normal SS7 routing
   procedures.

3.2.2.3 MTP3 Service Message (mtp3)

   The 'mtp3' opcode is used to deliver SS7 MSUs with a Service
   Indicator of 0-2, 4, 6-15 (non-SCCP, non-ISUP) over a TALI
   connection.  This opcode is only used on TALI protocol stacks that
   are implemented without SAAL.  The MTP3 layer of the SS7 MSU IS part
   of the data transferred across TCP/IP for this opcode; the data
   portion of the TALI 'mtp3' message begins with the SIO byte of the
   MTP3 header in the SS7 MSU.




Sprague, et al.              Informational                     [Page 29]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   +------------------------------------------------------------------+
   | Octets | Field Name  | Description                               |
   +------------------------------------------------------------------+
   | 0..3   | SYNC        | 'TALI'                                    |
   +------------------------------------------------------------------+
   | 4..7   | OPCODE      | 'mtp3'                                    |
   +------------------------------------------------------------------+
   | 8..9   | LENGTH      | Length                                    |
   +------------------------------------------------------------------+
   | 10..X  | Layer 3 MSU | Raw MSU data starting at the Layer 3 SIO  |
   |        | Data        | field.                                    |
   +------------------------------------------------------------------+

3.2.2.3.1 MTP3 Encapsulation using TALI

   When an SS7 MSU with SI=0-2,4,6-15 arrives at an SG from a 56 Kbps or
   DS1 link and is routed within the SG to an IP device, the SG performs
   the following processing on the SS7 MSU:

   *  discards the MTP Layer 2 information, CRC and flags

   *  places MTP Layer 3 into the SERVICE payload area of TALI packet

   *  The SYNC field is set

   *  The OPCODE is set to 'mtp3'

   *  The LENGTH is set to the number of octets in the SERVICE field

   Once the fully formed 'mtp3' TALI packet is created, it is handed to
   the TCP socket layer and transmitted.  The transmission process will
   add TCP, IP and MAC header information.



















Sprague, et al.              Informational                     [Page 30]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


                             SS7 MSU

           |      Layer 3              |     Layer 2      |
           |                           |                  |
      +----+---+-----------+-------+---+--+---+---+---+---+----+
      |Flag|FCS|Other Layer|Routing|SIO|LI|FIB|FSN|BIB|BSN|Flag|
      |    |   |3 Data     |Label  |   |  |   |   |   |   |    |
      +----+---+-----------+-------+---+--+---+---+---+---+----+
               |                       /
               |                 ------
               |                /
        TALI   +----------------+---+------+----+
        Packet |  Service       |LEN|Opcode|SYNC|
               +----------------+---+------+----+
               |                                /
               |                              --
               |                             /
               +----------------------------+------+------+------+
        IP     | TALI Packet                |TCP   | IP   | MAC  |
        Packet |                            |Header|Header|Header|
               +----------------------------+------+------+------+

      Figure 8: Encapsulation of SS7 MSUs with SI!=3,5,13 using 'mtp3'

   When an 'mtp3' TALI packet is received by an SG from an IP device,
   the SG performs the following processing on the 'mtp3' packet:

   *  validates the TALI header

   *  Allocates space for a new SS7 message

   *  extracts the MTP Layer 3 data from the SERVICE area and places it
      in the new SS7 message

   Once the 'mtp3' packet is transformed back into a normal SS7 MSU, the
   MSU is routed within the SG according to the normal SS7 routing
   procedures.

3.2.2.4 SAAL Service Message (saal)

   The 'saal' opcode is used to deliver SS7 MSUs with any Service
   Indicator over a TALI connection.  This opcode is only used on TALI
   protocol stacks that are implemented with SAAL.  The 'saal' opcode is
   also used to transmit SAAL peer to peer packets (SSCF peer to peer
   packets and SSCOP peer to peer packets other than SS7 service data)
   over a TALI connection.





Sprague, et al.              Informational                     [Page 31]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   When used to transfer SS7 MSUs, the MTP3 layer of the SS7 MSU IS part
   of the data transferred across TCP/IP for this opcode; the data
   portion of the TALI 'saal' message begins with the SIO byte of the
   MTP3 header in the SS7 MSU and ends with the last byte of the SSCOP
   trailer.

   When used to transfer SSCF/SSCOP peer to peer messages the data
   portion of the TALI 'saal' message includes the entire SSCOP PDU.

   +------------------------------------------------------------------+
   | Octets | Field Name  | Description                               |
   +------------------------------------------------------------------+
   | 0..3   | SYNC        | 'TALI'                                    |
   +------------------------------------------------------------------+
   | 4..7   | OPCODE      | 'saal'                                    |
   +------------------------------------------------------------------+
   | 8..9   | LENGTH      | Length                                    |
   +------------------------------------------------------------------+
   | 10..X  | Layer 3     | Raw MSU data starting at the Layer 3 SIO  |
   |        | Data        | field.                                    |
   +------------------------------------------------------------------+
   | (X+1)  | SSCOP       | Zero (0) to three (3) octets of padding   |
   |  ..Y   | Trailer     | plus 4 octets for the trailer data.  The  |
   |        |             | total length of the Layer 3 Data and the  |
   |        |             | SSCOP trailer must be a multiple of 4.    |
   +------------------------------------------------------------------+

                        or

   +------------------------------------------------------------------+
   | Octets | Field Name  | Description                               |
   +------------------------------------------------------------------+
   | 0..3   | SYNC        | 'TALI'                                    |
   +------------------------------------------------------------------+
   | 4..7   | OPCODE      | 'saal'                                    |
   +------------------------------------------------------------------+
   | 8..9   | LENGTH      | Length                                    |
   +------------------------------------------------------------------+
   | 10..X  | SAAL Peer   | Raw SSCF/SSCOP peer to peer packets are   |
   |        | to Peer     | also transferred over the TALI connection |
   |        | message     | using this 'saal' opcode.                 |
   +------------------------------------------------------------------+

3.2.2.4.1 MTP3 and SAAL Peer to Peer Encapsulation using TALI

   When an SS7 MSU (with any SI) arrives at an SG from a 56 Kbps or DS1
   link and is routed within the SG for transmission to an IP device,
   the SG performs the following processing on the SS7 MSU:



Sprague, et al.              Informational                     [Page 32]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   *  discards the MTP Layer 2 information, CRC and flags

   *  the MSU is passed from an MTP3 processing software layer to the
      SSCF and SSCOP layers (the SAAL layers).  These layers convert the
      SS7 MSU into an SSCOP PDU.  Part of this conversion includes
      adding an SSCOP trailer.

   *  the SSCOP PDU (whether it is a peer to peer SAAL message or SS7
      MSU in an SSCOP PDU) is copied into the SERVICE payload area of
      the TALI packet

   *  The SYNC field is set

   *  The OPCODE is set to 'saal'

   *  The LENGTH is set to the number of octets in the SERVICE field

   Once the fully formed 'saal' TALI packet is created, it is handed to
   the TCP socket layer and transmitted.  The transmission process will
   add TCP, IP and MAC header information.

   Since the routing information is placed in the TALI Packet, no
   routing information needs to be saved by the SG.




























Sprague, et al.              Informational                     [Page 33]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


                               SS7 MSU

           |          Layer 3          |     Layer 2      |
           |                           |                  |
      +----+---+-----------+-------+---+--+---+---+---+---+----+
      |Flag|FCS|Other Layer|Routing|SIO|LI|FIB|FSN|BIB|BSN|Flag|
      |    |   |3 Data     |Label  |   |  |   |   |   |   |    |
      +----+---+-----------+-------+---+--+---+---+---+---+----+
               |                       |
               |                       |
               |                       |
       +-------+-----------------------+
       |SSCOP  |  Service              |
       |Trailer|                       |
       +-------+-----------------------+
       |                               |
       +-------+-----------------------+---+------+----+
       |Service with SSCOP Trailer     |LEN|Opcode|SYNC|
       +-------+-----------------------+---+------+----+
       |                                               /
       |                              -----------------
       |                             /
       +----------------------------+------+------+------+
       | TALI Packet                |TCP   | IP   | MAC  |
       |                            |Header|Header|Header|
       +----------------------------+------+------+------+

   Figure 9: Encapsulation of SAAL PDUs using the TALI 'saal' opcode

   When an 'saal' TALI packet is received at the SG from an IP device,
   the SG performs the following processing on the 'saal' packet:

   *  validates the TALI header

   *  Allocates space for a new SSCOP PDU message

   *  extracts the SSCOP PDU data from the SERVICE area and places it in
      the new SSCOP PDU message

   Once the 'saal' packet is transformed back into a normal DS1 SSCOP
   PDU, the SSCOP PDU is passed to the SAAL layer for receive
   processing.  If the SSCOP PDU is a peer to peer pdu, it is processed
   completely in the appropriate SAAL layer.  If the SSCOP PDU is an SS7
   MSU, the MSU is transformed back to a normal SS7 MSU and is routed
   within the SG according to the normal SS7 routing procedures.






Sprague, et al.              Informational                     [Page 34]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


3.3 TALI Timers

   Version 1.0 of the TALI specification defined 4 TALI timers that are
   used as part of the TALI state machine.  These timers are generically
   named 'T1' through 'T4'.  Brief descriptions of each timer are
   provided in the following subsections.  Timer expiration events for
   each of the T1-T4 timers appear as inputs to the TALI state machine.
   For exact processing of each timer (when to start/stop, how to
   process timer expirations), refer to the TALI state machine.

   Both ends of the TALI connection have there own T1-T4 timers.  The
   T1-T4 timer values can be set on each end of the connection
   independent of the settings on the far end.  For each timer, a
   default value and range is recommended in the following sections.

3.3.1 T1 Timer

   The T1 timer represents the time interval between the origination of
   a 'test' message at each TALI implementation.  Each time T1 expires,
   the TALI implementation should send a 'test'.

3.3.2 T2 Timer

   The T2 timer represents the amount of time that the Peer has to
   return an 'allo' or a 'proh' in response to a 'test'.  If the far end
   fails to reply with 'allo' or 'proh' before T2 expires, the sender of
   the 'test' treats the T2 expiration as a protocol violation.  Note
   that T2 must be < T1 in order for these timers to work as designed.

3.3.3 T3 Timer

   The T3 timer controls how long the near end should continue to
   process Service Data that is received from the far end after a
   Management Prohibit Traffic Event has occurred (at the near end).
   This timer is used when a transition from NEA-FEA (both ends allowed
   to send service data) to NEP-FEA (only far end willing to send
   service data) occurs.  On that transition, it is reasonable to expect
   that the far end needs some amount of time to adjust its TALI state
   machine and divert service data traffic away from this socket.  The
   T3 timer controls the amount of time the far end has to divert
   traffic.

3.3.4 T4 Timer

   The T4 timer represents the time interval between the origination of
   a 'moni' message at each TALI implementation.  Each time T4 expires,
   the TALI implementation should send a 'moni'.




Sprague, et al.              Informational                     [Page 35]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


3.3.5 Recommended Defaults and Ranges for the TALI Timers

   The following table provides the recommended default and configurable
   range for each TALI timer.

   +------------------------------------------------------------------+
   |Name|  Min  |  Max  |Default| Description                         |
   +------------------------------------------------------------------+
   | T1 | 100ms | 60sec | 4 sec | Send test PDU timer                 |
   +------------------------------------------------------------------+
   | T2 | 100ms | 60sec | 3 sec | Response timer for an allo or proh  |
   |    |       |       |       | response to test message.           |
   +------------------------------------------------------------------+
   | T3 | 100ms | 60sec | 5 sec | Timer controls how long to process  |
   |    |       |       |       | rcvd serv data after an NE          |
   |    |       |       |       | transition from NEA to NEP.  System |
   |    |       |       |       | is waiting for a proa response to   |
   |    |       |       |       | the first proh send when NE         |
   |    |       |       |       | transitions from NEA to NEP.        |
   +------------------------------------------------------------------+
   | T4 | 100ms | 60sec |10 sec | Send moni PDU timer                 |
   +------------------------------------------------------------------+

                         Table 5: Timers

   NOTE: The value of T1 must be at least one (1) millisecond greater
   than T2.  This is to prevent the system from a lockup in the T1
   expired condition.  If T1 is equal or less than T2, it will expire
   and restart T2 and not enforce responses to the test message.

   Enforcement of minimum and maximum timer values is implementation
   dependent.

3.4 TALI User Events

   Each TALI implementation must provide several user event controls
   over the behavior of the TALI state machine for each TALI connection.
   The user interface to provide these capabilities is implementation
   specific.

3.4.1 Management Open Socket Event

   The 'mgmt open socket' event, together with the 'mgmt close socket'
   event, allows the user to control when each defined TALI connection
   will form a TCP socket connection.  When 'open socket' for a
   particular TALI connection occurs, the TALI connection should begin
   trying to form a TCP socket connection to the peer.




Sprague, et al.              Informational                     [Page 36]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   The steps that are taken to connect are dependent on the
   client/server role of that end of the TALI connection.  The exact
   steps to perform these tasks are implementation dependent and may
   differ based on the TCP stack being used.

   In general, TALI clients form socket connections by using the BSD
   sockets calls:

         Socket()
         Bind()
         Connect()

   In general, TALI servers form socket connections by using the BSD
   sockets calls:

         Socket()
         Bind()
         Listen()
         Accept()

3.4.2 Management Close Socket Event

   The 'mgmt close socket' event can be issued by the user when it is
   desired that the TCP socket for a TALI socket, be closed immediately,
   or discontinue its attempts to connect to the peer.  After acting on
   'close socket', the TALI connection will not be established until
   'mgmt open socket' is issued.

3.4.3 Management Allow Traffic Event

   The 'mgmt allow traffic' event, together with the 'mgmt prohibit
   traffic' event, allows the user to control when each defined TALI
   connection will be willing to carry SS7 service data over that
   particular TALI connection.  When 'mgmt allow traffic' is issued, the
   TALI implementation becomes willing to carry service data.  The TALI
   state for the near end should transition to NEA (near end allowed) if
   the connection is already established.

3.4.4 Management Prohibit Traffic Event

   The 'mgmt prohibit traffic' event is the opposite of 'allow traffic'.
   When 'mgmt prohibit traffic' is issued, the TALI implementation
   becomes un-willing to carry SS7 service data over that particular
   TALI connection.  The TALI state for the near end should transition
   to NEP (near end prohibited) if the connection is already
   established.





Sprague, et al.              Informational                     [Page 37]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


3.5 Other Implementation Dependent TALI Events

   In addition to timers, each TALI implementation needs to be able to
   detect, and react accordingly, for the following events:

   *  Connection Established.  When the TCP socket connection is
      initially established the TALI state machine must be notified.

   *  Connection Lost.  When the TCP socket connection is lost, due to
      socket errors during reads/writes, the TALI state machine must be
      notified.

   *  Protocol Violations.  Any violation of the TALI protocol as
      discussed in 3.7.1.3.

3.6 TALI States

   The TALI version 1.0 specification is based on a state machine that
   considers 6 TALI states.  Each end of the TALI connection maintains
   its own TALI state.































Sprague, et al.              Informational                     [Page 38]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   +------------------------------------------------------------------+
   | Name       | Description                                         |
   +------------------------------------------------------------------+
   | OOS        | The TALI connection is out of service.  This usually|
   |            | corresponds to a user event to 'close' the socket,  |
   |            | or a user event to 'deactivate the SS7 link'.       |
   +------------------------------------------------------------------+
   | Connecting | The TALI layer is attempting to establish a TCP     |
   |            | socket connection to the peer.  Servers are         |
   |            | 'accepting', clients are 'connecting'.              |
   +------------------------------------------------------------------+
   | NEP-FEP    | The TCP socket connection is established.  Neither  |
   |            | side of the connection is ready to use the socket   |
   |            | for service PDUs.                                   |
   +------------------------------------------------------------------+
   | NEP-FEA    | The TCP socket connection is established.  The NE is|
   |            | not ready to use the socket for service PDUs.  The  |
   |            | FE is ready to use the socket for service PDUs.     |
   +------------------------------------------------------------------+
   | NEA-FEP    | The TCP socket connection is established.  The NE is|
   |            | ready to use the socket for service PDUs.  The FE is|
   |            | not ready to use the socket for service PDUs.       |
   +------------------------------------------------------------------+
   | NEA-FEA    | The TCP socket connection is established.  Both     |
   |            | sides are ready to use the socket for service PDUs. |
   |            | This is the only state where normal bi-directional  |
   |            | SS7 data transfer occurs.                           |
   +------------------------------------------------------------------+

                              Table 6: TALI States

3.7 TALI Version 1.0 State Machine

   This section provides the state machine that must be followed by each
   TALI implementation in order to be compliant with this specification.

3.7.1 State Machine Concepts

   Before presenting the actual state machine, several concepts are
   discussed.

3.7.1.1 General Protocol Rules

   1.  Neither side can send service data unless both sides are allowed.

   2.  Each side initializes to the prohibited state for both near end
       and far end.




Sprague, et al.              Informational                     [Page 39]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   3.  State changes between the NEx-FEx states are signaled with either
       an 'allo' or 'proh'.

   4.  Each side can poll the far end's state with a 'test'.  Upon
       sending 'test', T1 and T2 should always be restarted.

   5.  Each side polls the far end with a 'test' every T1 expiration.

   6.  The reply to a 'test' is based on the state of the near end only.

   7.  The reply to a 'test' is either 'allo' or 'proh'.

   8.  A far end signals the last service PDU has been transmitted with
       either a 'proh' or a 'proa'.

   9.  Upon receiving a 'proh', the receiver must always reply with
       'proa'.

   10. The NE cannot gracefully close a socket unless a 'proh' is sent
       and 'proa' is received.

   11. On the transition from NEA to NEP, after sending a 'proh', the
       near end must continue to process received service data until a
       'proa' is received or until a T3 timer expires.

3.7.1.2 Graceful Shutdown of a Socket

   The state table treats a management request to close the socket as a
   'hard' shutdown.  That is, it will close the socket immediately
   regardless of the current state.  Therefore, the correct steps to
   ensure a graceful shutdown of a socket (from the NEA_FEP or NEA_FEA
   states) is:

   1. Management issues a Management Prohibit Traffic Event on the
      socket.

   2. Management will wait for T3 to expire.

   3. Management can then issue a Close Socket Event on the socket.

3.7.1.3 TALI Protocol Violations

   Each TALI implementation must detect when violations of the TALI
   protocol have occurred and react accordingly.  Protocol violations
   include:

   *  Invalid sync code in a received message




Sprague, et al.              Informational                     [Page 40]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   *  Invalid opcode in a received message

   *  Invalid length field in a received message

   *  Not receiving an 'allo' or 'proh', in response to the origination
      of a 'test' , before the T2 timer expires

   *  Receiving Service Messages on a prohibited socket.

   *  TCP Socket errors - Connection Lost

   In the state machine that follows, State/Event combinations that
   should be treated as protocol violations are indicated via a 'PV' in
   the state/event cell.  All of the 'PV' events are then processed as
   per the 'Protocol Violation' row in the table.

3.7.2 The State Machine

   Internal Data required for State Machine:

   boolean sock_allowed.  This flag indicates whether the NE is allowed
   to carry Service Messages.

   Initial Conditions:
   sock_allowed = FALSE
   state = OOS
   no timers running

   +------------------------------------------------------------------+
   |   State| OOS  |Connecting| NEP-FEP | NEP-FEA | NEA-FEP | NEA-FEA |
   |Event   |      |          |         |         |         |         |
   +------------------------------------------------------------------+
   |T1 Exp. |      |          |Send test|Send test|Send test|Send test|
   |        |      |          |Start T1 |Start T1 |Start T1 |Start T1 |
   |        |      |          |Start T2 |Start T2 |Start T2 |Start T2 |
   +------------------------------------------------------------------+
   |T2 Exp. |      |          |   PV    |   PV    |   PV    |   PV    |
   +------------------------------------------------------------------+
   |T3 Exp. |      |          |   PV    |   PV    |         |         |
   +------------------------------------------------------------------+
   |T4 Exp. |      |          |Send moni|Send moni|Send moni|Send moni|
   |        |      |          |Start T4 |Start T4 |Start T4 |Start T4 |
   +------------------------------------------------------------------+
   |Rcv test|      |          |Send proh|Send proh|Send allo|Send allo|
   +------------------------------------------------------------------+
   |Rcv allo|      |          | Stop T2 | Stop T2 | Stop T2 | Stop T2 |
   |        |      |          | NEP-FEA |         | NEA-FEA |         |




Sprague, et al.              Informational                     [Page 41]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   +------------------------------------------------------------------+
   |Rcv proh|      |          | Stop T2 | Stop T2 | Stop T2 | Stop T2 |
   |        |      |          |Send proa|Send proa|Send proa|Flush or |
   |        |      |          |         | NEP-FEP |         | reroute |
   |        |      |          |         |         |         |Send proa|
   |        |      |          |         |         |         | NEA-FEP |
   +------------------------------------------------------------------+
   |Rcv proa|      |          | Stop T3 | Stop T3 |         |         |
   +------------------------------------------------------------------+
   |Rcv moni|      |          |Convert  |Convert  |Convert  |Convert  |
   |        |      |          | to mona | to mona | to mona | to mona |
   |        |      |          |Send mona|Send mona|Send mona|Send mona|
   +------------------------------------------------------------------+
   |Rcv mona|      |          |Implemen-|Implemen-|Implemen-|Implemen-|
   |        |      |          |tation   |tation   |tation   |tation   |
   |        |      |          |dependent|dependent|dependent|dependent|
   +------------------------------------------------------------------+
   |Rcv     |      |          |   PV    |If T3 run|   PV    |Process  |
   | Service|      |          |         | Process |         |         |
   |        |      |          |         |Else PV  |         |         |
   +------------------------------------------------------------------+
   |Connect.|      | Start T1 |         |         |         |         |
   |Estab.  |      | Start T2 |         |         |         |         |
   |        |      | Start T4 |         |         |         |         |
   |        |      |(if non-0)|         |         |         |         |
   |        |      |if sock_  |         |         |         |         |
   |        |      |  allowed |         |         |         |         |
   |        |      |  = TRUE  |         |         |         |         |
   |        |      | send allo|         |         |         |         |
   |        |      | send test|         |         |         |         |
   |        |      | NEA-FEP  |         |         |         |         |
   |        |      |else      |         |         |         |         |
   |        |      | send proh|         |         |         |         |
   |        |      | send test|         |         |         |         |
   |        |      | NEP-FEP  |         |         |         |         |
   +------------------------------------------------------------------+
   |Connect.|      |          |   PV    |   PV    |   PV    |   PV    |
   |Lost    |      |          |         |         |         |         |
   +------------------------------------------------------------------+
   |Protocol|      |          |Stop all |Stop all |Stop all |Stop all |
   |Violat. |      |          | timers  | timers  | timers  | timers  |
   |        |      |          |Close the|Close the|Close the|Close the|
   |        |      |          | socket  | socket  | socket  | socket  |
   |        |      |          |Connect- |Connect- |Connect- |Connect- |
   |        |      |          |  ing    |  ing    |  ing    |  ing    |






Sprague, et al.              Informational                     [Page 42]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   +------------------------------------------------------------------+
   |Mgmt.   |Open  |          |         |         |         |         |
   |Open    |socket|          |         |         |         |         |
   |Socket  |Conne-|          |         |         |         |         |
   |        | cting|          |         |         |         |         |
   +------------------------------------------------------------------+
   |Mgmt.   |      |Close the |Stop all |Stop all |Stop all |Stop all |
   |Close   |      | socket   | timers  | timers  | timers  | timers  |
   |Socket  |      |OOS       |Close the|Close the|Close the|Close the|
   |        |      |          | socket  | socket  | socket  | socket  |
   |        |      |          |OOS      |OOS      |OOS      |OOS      |
   +------------------------------------------------------------------+
   |Mgmt.   |sock_ |sock_allo-|sock_all-|sock_all-|sock_all-|sock_all-|
   |Prohibit|allow-| wed=FALSE| owed=   | owed=   | owed=   | owed=   |
   |Socket  |ed =  |          | FALSE   | FALSE   | FALSE   | FALSE   |
   |        |FALSE |          |         |         |send proh|send proh|
   |        |      |          |         |         |start t3 |start t3 |
   |        |      |          |         |         | NEP-FEP | NEP-FEA |
   |        |      |          |         |         |         |         |
   +------------------------------------------------------------------+
   |Mgmt.   |sock_ |sock_allo-|sock_all-|sock_all-|sock_all-|sock_all-|
   |Allow   |allow-| wed=TRUE | owed=   | owed=   | owed=   | owed=   |
   |Traffic |ed =  |          | TRUE    | FALSE   | TRUE    | TRUE    |
   |        |TRUE  |          |send allo|send allo|         |         |
   |        |      |          | NEA-FEP | NEA-FEA |         |         |
   +------------------------------------------------------------------+
   |User    |reject| reject   | reject  | reject  | reject  | send    |
   |Part    |data  | data     | data    | data    | data    | data    |
   |Msgs.   |      |          |         |         |         |         |
   +------------------------------------------------------------------+

                     Table 7: TALI 1.0 State Machine

3.8 TALI 1.0 Implementation Notes

   Several aspects of the expected TALI 1.0 implementation have not been
   specifically addressed in the state machine or previous text (or else
   they were presented but will be reiterated here).  These
   implementation notes in some cases have to do with the expected
   behavior of the software layer above the TALI layer.

3.8.1 Failure on a TCP/IP Socket

   *  The failure to read or write from a TCP socket shall be detected
      and generate a connection lost event.






Sprague, et al.              Informational                     [Page 43]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


3.8.2 Congestion on a TCP/IP Socket

   *  Message streams can be monitored for congestion via implementation
      dependent methods.

   *  One possible definition of congestion for the previous requirement
      might be when a TCP socket is blocked.

3.9 TALI 1.0 Limitations

   Several limitations with the TALI 1.0 specification and
   implementation are identified:

   *  For SCCP traffic, only UDT and XUDT Class 0 and Class 1 traffic
      should be managed by this protocol.

   *  When the MTP3 Routing Label is not part of the data transmitted
      across the wire, priority zero (0) traffic is used for all traffic
      when the SIO is regenerated.

4. TALI Version 2.0

   Version 2.0 of the TALI specification provides several additions to
   the Version 1.0 specification.  The 2.0 additions are provided by
   introducing three new TALI opcodes.  The basic functionality and most
   of the details of the TALI 1.0 implementation are NOT changed by the
   2.0 additions.
























Sprague, et al.              Informational                     [Page 44]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   The table below provides a summary of the messages and message
   structure used in TALI version 2.0.

   +------------------------------------------------------------------+
   | OCTET | DESCRIPTION           | SIZE     | VALUE  |    TYPE      |
   +------------------------------------------------------------------+
   | 0..3  | SYNC                  | 4 Octets |        | 4 byte ASCII |
   +------------------------------------------------------------------+
   |       |   TALI                |          | 'TALI' |              |
   +------------------------------------------------------------------+
   | 4..7  | OPCODE                | 4 Octets |        | 4 byte ASCII |
   +------------------------------------------------------------------+
   |       |   Test Service        |          | 'test' |              |
   |       |   Allow Service       |          | 'allo' |              |
   |       |   Prohibit Service    |          | 'proh' |              |
   |       |   Prohibit Service Ack|          | 'proa' |              |
   |       |   Monitor Socket      |          | 'moni' |              |
   |       |   Monitor Socket Ack  |          | 'mona' |              |
   |       |   SCCP Service        |          | 'sccp' |              |
   |       |   ISUP Service o/TALI |          | 'isot' |              |
   |       |   MTP3 Service o/TALI |          | 'mtp3' |              |
   |       |   Service o/SAAL      |          | 'saal' |              |
   |       |   Management Message  |          | 'mgmt' |              |
   |       |   Extended Service Msg|          | 'xsrv' |              |
   |       |   Special Message     |          | 'spcl' |              |
   +------------------------------------------------------------------+
   | 8..9  | LENGTH                | 2 Octets |        | integer      |
   |       |   (least significant  |          |        |              |
   |       |    byte first) non-0  |          |        |              |
   |       |    if Service or      |          |        |              |
   |       |    Socket monitor msg |          |        |              |
   +------------------------------------------------------------------+
   | 10..X | DATA PAYLOAD          | variable |        | variable     |
   +------------------------------------------------------------------+

   Due to the minimal amount of change from 1.0, this chapter will only
   provide:

   *  Detailed information regarding how a TALI implementation can
      identify itself as a 2.0 vs. a 1.0 implementation

   *  Detailed information regarding how to provide backward
      compatibility for a connection to a far end that is only TALI 1.0
      capable

   *  Detailed information regarding the new 2.0 opcodes





Sprague, et al.              Informational                     [Page 45]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   *  Detailed information regarding any other changes to the
      information presented in previous sections that need to be
      implemented in order to be 2.0 compatible.

   Therefore, readers of this chapter should read this from the point of
   view of modifying an existing TALI 1.0 implementation to support the
   new 2.0 features.

4.1 Overview of TALI Version 2.0 Features

   A small number of changes to a 1.0 TALI implementation are required
   to support 2.0.  Figure 10 illustrates the inputs that affect the 2.0
   TALI State Machine.  The reader may notice that the only differences
   from the inputs for 1.0 are as follows:

   Three new TALI opcodes can be sent/received between a TALI node and
   its peer.  The new opcodes are:

   *  'mgmt'
   *  'xsrv'
   *  'spcl'

   Three new User Part capabilities need to be supported by the layer of
   code above the TALI layer in each implementation.  The user part
   needs to provide support for 'mgmt', 'xsrv', and 'spcl' data.

   More information about the 3 new opcodes is provided in individual
   sections in this chapter.  However, a brief description of the
   purpose of each of these opcodes is as follows:

   *  'mgmt' - This opcode is intended to allow MANAGEMENT data, or data
      that will manage the operation of the device, to pass between the
      TALI endpoints.  Examples of this management data include:

      *  configuration data, such as which SS7 traffic streams a peer
         would like to receive over a specific socket

      *  SS7 Network Management data, such as information regarding
         point code (un)availability and congestion.

      *  Enabling/disabling various socket options, such as options
         regarding which messages are supported, or how to format data.









Sprague, et al.              Informational                     [Page 46]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   *  'xsrv' - Extended Service Opcodes.  It is envisioned that the TALI
      protocol could be extended to carry other types of traffic that
      are not covered by the 1.0 service data opcodes ('sccp', 'isot',
      'mtp3', or 'saal').  By defining a new 'xsrv' service opcode, the
      TALI protocol is opened up to the possibility of being used for
      other types of data transport.

   *  'spcl' - Special services.  It is envisioned that vendors may want
      to build special services into their TALI implementations that are
      only activated when the implementation is connected to other
      equipment implementing the same special services.  This opcode is
      intended to provide a general means to discover more information
      regarding who the TALI session is connected to, and a means to
      enable special features based on the vendor/implementation on the
      far end.




































Sprague, et al.              Informational                     [Page 47]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   +====+    +---------+                    +============+
   |    |    | Service | +-------------+    |            |
   |User|    | Message,| | Mgmt. Open  |    | MANAGEMENT |
   |Part|<-->| MGMT,   | | Mgmt. Close |<-->|            |
   |    |    | XSRV,   | | Mgmt. Proh. |    |            |
   |    |    | SPCL    | | Mgmt. Allow |    +============+
   +====+    +---------+ +-------------+
                   ^            ^
                   |            |
                   v            v
   +========================================================+
   |                 TALI State Machine                     |
   +========================================================+
         ^               ^                 ^             ^
         |               |                 |             |
         v               |                 |             |
    +---------+          |                 |             |
    | Received|   +-----------------+ +-----------+ +------------+
    | 'test', |   | Connection est. | | Protocol  | | T1 Expired |
    | 'allo', |   | Connection lost | | Violation | | T2 Expired |
    | 'proh', |   |                 | |           | | T3 Expired |
    | 'proa', |   +-----------------+ +-----------+ | T4 Expired |
    | 'moni', |          ^                  ^       +------------+
    | 'mona', |          |                  |             ^
    | 'mgmt', |          |                  |             |
    | 'xsrv', |          |                  |             |
    | 'spcl', |          |                  |             |
    |   or    |    +========================================+
    | Service |    |         IMPLEMENTATION                 |
    | Message |    |           DEPENDENT                    |
    +---------+    +========================================+
         ^
         |
         v
     +============+
     |    PEER    |
     |            |
     +============+

     Figure 10: Overview of Inputs to the TALI 2.0 State Machine

4.2 TALI Version Identification

   The TALI 1.0 specification did not provide a simple means to perform
   TALI version identification.  However, the general purpose 'moni'
   message from 1.0 can be used to solve this problem in 2.0.





Sprague, et al.              Informational                     [Page 48]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   Recall from 1.0 that the 'moni' message was very loosely defined in
   the 1.0 spec:

   *  The primary purpose of the 'moni' message was to provide a general
      purpose ECHO capability.  It was envisioned that an important task
      that the ECHO capability could provide would be to measure Round
      Trip TALI/TALI processing time.

   *  The data portion of the 'moni' message could be from 0-200 bytes
      long.  The use of the data area was completely implementation
      specific.

   *  There were no requirements that an implementation ever send a
      'moni'.

   *  If an implementation did send 'moni', it should use the T4 timer
      to control the frequency of the outgoing 'moni'.

   *  The receiver of the 'moni' should not make any assumptions as to
      the data portion of the 'moni'.  The receiver should simply
      convert the 'moni' into a 'mona' and return the message with the
      same data portion.

   TALI 2.0 implementations should use the 'moni' message to provide
   version identification as per the following bullets:

   *  The primary purpose of the 'moni' message is now twofold:

   *  To provide version identification

      *  To continue to provide a general purpose ECHO capability that
         can be used to measure Round Trip time or perform other
         implementation specific tasks.

   *  The data portion of the 'moni' message is now divided into 2
      portions

      *  A portion dedicated to version identification, 12 bytes long,
         with a specific format that must be followed

      *  Followed by a free format section that can be used in a
         completely implementation specific manner.

   *  The overall length of the data portion for a 'moni' should still
      not exceed 200 bytes.  This is required to maintain backward
      compatibility with 1.0 implementations that may check for a
      maximum length of 200 bytes on the 'moni' opcode.




Sprague, et al.              Informational                     [Page 49]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   *  If a TALI implementation wants to identify itself as a version 2.0
      node, it must send a 'moni' encoded as per Table 8.  Every 'moni'
      it sends should conform to the encoding in Table 8.  The version
      label should not change from 'moni' to 'moni'.  The data following
      the version label can change from 'moni' to 'moni' and can
      continue to be used for RTT calculations, or other purposes.

   *  If a TALI implementation is trying to determine if the far end of
      the TALI connection has implemented version 2.0, the
      implementation must examine any received 'moni' messages that
      arrive from the far end and see if they conform to the new
      stricter 'moni' encoding in Table 8.  On receiving 'moni', a TALI
      2.0 node will compare the 12 bytes of data in the VER LABEL field
      with a list of predetermined strings to determine the
      functionality of the TALI node it is connected to.  If the data
      doesn't match any of the predetermined strings, the Far End is
      assumed to be a TALI 1.0 node.

   *  Each TALI implementation must assume that the far end of the
      connection is a 1.0 implementation until an arriving 'moni'
      announces that the far end supports TALI version 2.0.  If a 'moni'
      never arrives, the implementation knows the far end has
      implemented version 1.0 of the specification.

   *  TALI 1.0 implementations can receive newly encoded 'moni' messages
      and simply ignore the data.  The 1.0 implementations will continue
      to operate as if the far end is always a 1.0 node (ignore the data
      portion of the 'moni', convert 'moni' to 'mona', and return the
      'mona').

   *  The next section provides more information regarding backwards
      compatibility (2.0 implementations connected to devices that
      implemented version 1.0 of the specification).


















Sprague, et al.              Informational                     [Page 50]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   +------------------------------------------------------------------+
   | Octets | Field Name  | Description                  | Field Type |
   +------------------------------------------------------------------+
   | 0..3   | SYNC        | 'TALI'                       |4 byte ASCII|
   +------------------------------------------------------------------+
   | 4..7   | OPCODE      | 'moni'                       |4 byte ASCII|
   +------------------------------------------------------------------+
   | 8..9   | LENGTH      | Length (includes the version | Integer    |
   |        |             | label and data fields)       |            |
   +------------------------------------------------------------------+
   | 10..21 | Ver. Label  | 'vers xxx.yyy'               | 12 byte    |
   |        | See note    |                              | ASCII      |
   +------------------------------------------------------------------+
   | 22..X  | DATA        | Vendor Dependent             | Variable   |
   |        |             | Maximum length of this       |            |
   |        |             | message (as coded in octets 8|            |
   |        |             | -9, and stored in bytes 10-X)|            |
   |        |             | should not exceed 200 bytes. |            |
   +------------------------------------------------------------------+

               Table 8: Version Control 'moni' Message

   NOTE: xxx.yyy = provides the Major and Minor release number of the
                   TALI specification being implemented.
         001.000 = Tali version 1.0
         002.000 = Tali version 2.0     // this specification.
         002.001 = Tali version 2.1     // a minor change to 2.0
         003.000 = Tali version 3.0
         and so on.

   The 'vers 002.000' field is an 12 byte field of field type 'ascii
   text'.  As such, 'v' should be the first byte of the field that is
   transmitted out the wire.

4.3 Backwards Compatibility

   As part of adding new functionality to the TALI specification,
   backwards compatibility from TALI version 2.0 to version 1.0 is
   required.  Backwards compatibility is important since TALI 2.0 nodes
   may be connected to far ends that only support version 1.0; it is
   important that these 2 implementations continue to inter-operate, and
   that the 2.0 node falls back to supporting only 1.0 opcodes in this
   situation.

   The previous section described how a TALI 2.0 implementation can use
   the 'moni' it sends to identify itself as a 2.0 node and how it can
   use the 'moni' it receives to determine if the far end is also a 2.0




Sprague, et al.              Informational                     [Page 51]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   node.  In addition to the discussion in the previous section, the
   following bullets provide details regarding how backwards
   compatibility must be achieved:

   *  As documented in the version 1.0 specification, TALI 1.0
      implementations that receive TALI messages with 'mgmt', 'xsrv',
      and 'spcl' opcodes will treat the message as a Protocol Violation
      (invalid opcode received).  The Protocol Violation will cause the
      socket to be dropped immediately.

   *  It is therefore required that a 2.0 implementation only send
      'mgmt', 'xsrv', and 'spcl' opcodes, after it has used a received
      'moni' message to determine that the far end is a 2.0 (or later)
      implementation and has identified itself as a 2.0 (or later)
      implementation.

   *  Each TALI 2.0 implementations must use the 'moni' as described in
      the previous section to identify themselves as 2.0, and to learn
      if the far end is 2.0.

   *  Each TALI 2.0 implementation should maintain a variable as part of
      its state machine, 'far_end_version'.  The 'far_end_version'
      should be initialized to 1.0 when the socket is established.  Each
      time a 2.0 implementation receives 'moni', it should update the
      'far_end_version' variable.  If the 'moni' did not contain a
      version label, the 'far_end_version' should be reset to 1.0.  If
      the 'moni' did contain a version label for 2.0 (or a later
      version), the 'far_end_version' should be set accordingly.

   *  Each time a 2.0 implementation receives a new 2.0 opcode ('mgmt',
      'xsrv', and 'spcl') from the far end, it should examine the '
      far_end_version'.  If the 'far_end_version' indicates the far end
      is a 1.0 implementation, the received TALI message should be
      treated as a Protocol Violation (invalid opcode).  If the
      'far_end_version' is 2.0 (or later), the 2.0 implementation should
      process the received 'mgmt/xsrv/spcl' according to that nodes
      capabilities for that opcode.

   *  Each time a 2.0 implementation receives a request to send a TALI
      message with a 2.0 opcode ('mgmt/xsrv/spcl') from a higher layer
      of software, it should examine the 'far_end_version'.  If the
      'far_end_version' indicates the far end is a 1.0 implementation,
      the request to send the 2.0 opcode should be denied or ignored (an
      implementation decision) and the 2.0 opcode must NOT be sent to
      the far end.  If the 'far_end_version' indicates the far end is
      2.0 (or later), the request can be satisfied and the TALI message
      with the 2.0 opcode can be sent to the far end.




Sprague, et al.              Informational                     [Page 52]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   *  Each TALI 2.0 implementation can provide a varying level of
      support for each of the three new 2.0 opcodes ('mgmt/xsrv/spcl').
      In other words, an implementation may wish to only support SOME OF
      the primitives within the new opcodes.  The level of support for
      each 2.0 opcode ('mgmt/xsrv/spcl') is independent of the other two
      2.0 opcodes.

   *  The basic message structure for TALI messages using the new 2.0
      opcodes is presented in Table 9.

   *  The minimal level of support that is required for each of the 2.0
      opcodes (mgmt/xsrv/spcl) is to be able to receive TALI messages
      with these opcodes, recognize the new opcode, and ignore the
      message without affecting the state machine.  The TALI state
      should not change.  The socket connection should stay up.  In
      other words, a 2.0 implementation can elect to ignore any received
      'mgmt/xsrv/spcl' messages, if that implementation does not care to
      support the capability intended by that particular opcode.

   *  A partial level of support for a 2.0 opcode could be implemented.
      Partial support may consist of understanding the data structure
      for the 2.0 opcode, but only supporting some of the variants of
      the opcode.  The message structure for each of the new 2.0 opcodes
      consists of an extra 'Primitive' field that follows the TALI
      opcode and message length fields.  Each 'Primitive' is used to
      differentiate a variant of the opcode.  It is envisioned that each
      new 2.0 opcode can be extended by adding new 'Primitives', as more
      capabilities are defined for the opcode, without having to add new
      TALI opcodes.  A 2.0 implementation may understand and be willing
      to act on some of the 'Primitives' for an opcode, but not others.
      Receiving variants of a 2.0 opcode that an implementation does not
      understand need to be ignored and not affect the 2.0 state
      machine.

   *  The full level of support for a 2.0 opcode could be implemented.
      This support would consist of understanding and fully supporting
      every 'Primitive' within the 2.0 opcode.














Sprague, et al.              Informational                     [Page 53]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   +------------------------------------------------------------------+
   | Octets | Field Name  | Description                  | Field Type |
   +------------------------------------------------------------------+
   | 0..3   | SYNC        | 'TALI'                       |4 byte ASCII|
   +------------------------------------------------------------------+
   | 4..7   | OPCODE      | 'mgmt', 'xsrv' or 'spcl'     |4 byte ASCII|
   +------------------------------------------------------------------+
   | 8..9   | LENGTH      | Length (length of the rest   | Integer    |
   |        |             | of this packet)              |            |
   +------------------------------------------------------------------+
   | 10..13 | Primitive   | 'wxyz', or a 4 byte text     |  4 byte    |
   |        | See note    | that is appropriate for the  |  ASCII     |
   |        |             | given opcode                 |            |
   +------------------------------------------------------------------+
   | 14..X  | DATA        | The content of the data area | Variable   |
   |        |             | is dependent on the opcode/  |            |
   |        |             | primitive combination        |            |
   +------------------------------------------------------------------+

       Table 9: Basic Message Structure for New 2.0 TALI Opcodes

   NOTE:  The Primitive field acts as a modifier for each opcode.
   Within an opcode, different operations or groups of operations can be
   defined and supported.  The Primitive identifies each different
   operation or set of operations.

4.3.1 Generating Protocol Violations based on Received Messages

   As implied by some of the bullets before Table 9, it is a goal of the
   2.0 TALI specification to relax some of the error checking associated
   with the processing of received TALI messages.

   Version 1.0 of this specification was very strict in detailing the
   fields that were checked for each received message.  As each received
   message was processed, the SYNC code, opcode and length field of the
   message was checked; if any of these fields were invalid an internal
   protocol violation was generated.  The processing of the protocol
   violation caused the socket to go down.  In addition to the 3
   specific checks (sync, opcode, length), the overall philosophy of
   version 1.0 was to treat any received data that the receiver did not
   understand, or which the receiver deemed to contain incorrectly coded
   fields as protocol violations.

   Version 2.0 introduces the possibility of partial support for
   opcodes, partial support for primitives, and partial support for
   various fields (such as support for ANSI Pt Codes, but not ITU Pt
   Codes).  Thus, the overall philosophy of how to treat received data
   that the receiver does not support needs to be relaxed from the



Sprague, et al.              Informational                     [Page 54]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   strict treatment in version 1.0.  Version 2.0 implementations should
   be more tolerant when they receive messages they do not support (or
   which they believe contain incorrectly coded fields).  This tolerance
   should include NOT treating these receives as protocol violations.

   Version 2.0 implementations should perform the following level of
   strict/loose checks on the received messages:

   *  Checks against the sync codes, opcodes and lengths for version 1.0
      and version 2.0 opcodes should be performed (against Table 3 and
      Table 11).  Invalid data in these fields should be treated as
      cause for protocol violations.

   *  Checks against the opcode field for messages with new 2.0 opcodes
      (mgmt/xsrv/spcl) should be performed to determine whether the
      message can be processed by the implementation.  If an
      implementation chooses to NOT support a particular 2.0 opcode, the
      received message should be discarded, internal data (such as
      measurements, logs of messages, user notifications) could record
      the event, and the TALI state should NOT be affected.

   *  Checks against the primitive field for messages with new 2.0
      opcodes (mgmt/xsrv/spcl) should be performed to determine whether
      the message can be processed by the implementation.  If an
      implementation does not understand a particular primitive, or has
      chosen NOT to implement the features for a particular primitive,
      the received message should be discarded, internal data (such as
      measurements, logs of messages, user notifications) could record
      the event, and the TALI state should NOT be affected.

   *  Checks against other field types in messages with new 2.0 opcodes
      (such as checking the encoding of a Point Code field for a valid
      Pt Code type) should also be performed in a 'soft' manner.  Errors
      found in individual fields should cause the received message to be
      discarded, internal data (such as measurements, logs of messages,
      user notifications) could record the event, and the TALI state
      should NOT be affected.

   The goals behind introducing this gentler treatment of errors in
   received data are as follows:

   *  To keep the socket up in order to perform the primary purpose of
      the connection (ie: to continue to transport SS7 data) in spite of
      improperly formatted/unsupported TALI messages related to other
      features/extensions/etc.






Sprague, et al.              Informational                     [Page 55]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   *  To allow applications to support and use some of the features for
      a particular TALI revision without requiring the application to
      implement all of the functionality for the TALI revision.

   *  To increase the extensibility of the protocol.  Looser receive
      checks are preferred in order to be able to add new primitives and
      new primitive operations as they are defined.

4.4 Overview of the TALI Message Structure

   The basic message structure for all TALI messages is unchanged with
   the addition of new 2.0 opcodes.  The base TALI header still consists
   of SYNC + OPCODE + LENGTH, as described in Table 2.

   The message structure for the new 2.0 opcodes was shown in Table 9.
   These messages define an extra required field, PRIMITIVE, that
   follows the LENGTH field of Table 2.

4.4.1 Types of TALI Fields

   Table 4 in the version 1.0 specification provided implementation
   notes for all the 'types of fields' found in the 1.0 specification.
   Version 2.0 of TALI continues to use all of the types provided in
   Table 4, and also defines some new fields that are used in TALI
   messages that use the new 2.0 opcodes.  The following table
   introduces the new field types that are introduced with version 2.0.
   The types in Table 10 are used in addition to the types in Table 4 to
   implement the 2.0 TALI protocol.























Sprague, et al.              Informational                     [Page 56]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   +-----------+------------------------------------------------------+
   |Field Type | Implementation Notes for that Type                   |
   +------------------------------------------------------------------+
   |SS7 Point  | Used to transmit point code information for ANSI or  |
   |Code       | ITU variants of point codes across the TALI interface|
   |           | * The point code structure is 4 bytes. Byte 3 is used|
   |           |   to identify the TYPE of point code. The actual     |
   |           |   point code is then encoded in bytes 0-2 (w/byte 0  |
   |           |   being the least significant byte and the first byte|
   |           |   transmitted across the wire)                       |
   |           | * Byte 3: encoding of the type of point code (PC)    |
   |           |   0 = an ANSI Full PC                                |
   |           |   1 = an ITU International Full PC w/ a 3/8/3 coding |
   |           |       scheme for zone/area/identifier                |
   |           |   2 = an ITU National Full PC w/ a raw 14 bit PC     |
   |           |   3 = unused                                         |
   |           |   4 = an ANSI Cluster PC                             |
   |           | * For ANSI Full PC w/byte 3=0.  These point codes are|
   |           |   24 bit point codes as follows:                     |
   |           |   Byte 2 = Network                                   |
   |           |   Byte 1 = Cluster                                   |
   |           |   Byte 0 = Member                                    |
   |           | * For ITU International Full PC (3/8/3) w/byte 3=1.  |
   |           |   These point codes use 14 bits (stored in the 14    |
   |           |   least significant bits in bytes 0&1).  Byte 2 is   |
   |           |   unused.  The 14 bits should be interpreted as 3    |
   |           |   bits of zone, 8 bits of area and 3 bits of         |
   |           |   signaling point identifier.  The 3 bits of         |
   |           |   signaling point identifier are the 3 least         |
   |           |   significant bits.                                  |
   |           | * For ITU National Full PC w/byte 3=2. These point   |
   |           |   codes use 14 bits (stored in the 14 least          |
   |           |   significant bits in bytes 0&1).  Byte 2 is unused. |
   |           |   The 14 bits represent a single 14-bit quantity that|
   |           |   constitutes the point code.                        |
   |           | * For unused w/byte 3=3.  Bytes 0 through 2 are      |
   |           |   undefined.                                         |
   |           | * For ANSI Cluster PC, w/byte 3=4.  These point codes|
   |           |   are 24 bit point codes as follows:                 |
   |           |   Byte 2 = Network                                   |
   |           |   Byte 1 = Cluster                                   |
   |           |   Byte 0 = 0. This field is ignored and should be    |
   |           |   coded as 0...all members of the cluster are implied|
   |           | * Byte 0 is the first byte that is transmitted across|
   |           |   the wire, followed by byte 1, byte 2, then byte 3. |






Sprague, et al.              Informational                     [Page 57]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   +------------------------------------------------------------------+
   |Bit-Field  | * Field containing an array of N bits, where N is a  |
   |           |   multiple of 8.  Bit-Field types should be          |
   |           |   transmitted such that the byte containing bits 0   |
   |           |   through 7 is transmitted across the wire first,    |
   |           |   followed by the byte containing bits 8 through 15, |
   |           |   etc.                                               |
   |           | * The software for each implementation should be     |
   |           |   written in a manner that accounts for the required |
   |           |   byte order of transmission (ie: the Big Endian/    |
   |           |   Little Endian characteristics of the processor need|
   |           |   to be dealt with in the software).                 |
   +------------------------------------------------------------------+
   |Version    |A TALI version label is a 12 byte ASCII text field.   |
   |Label      |The label is of a format 'vers xxx.yyy', where xxx.yyy|
   |           |are used to identify the version such as 002.000.  As |
   |           |with other ASCII text fields, the first byte of the   |
   |           |text field (the 'v') should be the first byte         |
   |           |transmitted out the wire.                             |
   +------------------------------------------------------------------+
   |Primitive  |Messages that use the new TALI 2.0 opcodes all have a |
   |           |4 byte text ASCII field referred to as a Primitive.   |
   |           |The Primitive acts as a modifier for the opcode. This |
   |           |allows a single opcode to be used to perform multiple |
   |           |actions.                                              |
   +------------------------------------------------------------------+
   |Primitive  |A Primitive can be used to specify either a specific  |
   |Operation  |action or a set of actions.  When the Primitive field |
   |           |is used to specify a set of actions, an operation     |
   |           |field is used to pick a specific operation within that|
   |           |group of actions. Operation fields are 4 byte integers|
   +------------------------------------------------------------------+
   |Private    |Various RFC documents have detailed a set of assigned |
   |Enterprise |numbers (RFC 1700, Assigned Numbers) and defined data |
   |Code       |structures (RFC 1155, Structure and Identification of |
   |(PEC)      |Management Information for IP-based Internets)        |
   |           |that are used on IP networks to provide network       |
   |           |management information.                               |
   |           |Network Management Object Identifiers (OID) are used  |
   |           |to recognize specific organizations, companies,       |
   |           |protocols, and so on, in a manner that all vendors can|
   |           |agree on.                                             |
   |           |An Object Identifier exists which uniquely describes  |
   |           |each company that does business in the data/telecomm  |
   |           |industry.  That OID is referred to as an 'SMI Network |
   |           |Management Private Enterprise Code', which we are     |
   |           |shortening to Private Enterprise Code of PEC in this  |
   |           |document for simplicity.  Each PEC is assumed to have |



Sprague, et al.              Informational                     [Page 58]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   |           |a defined prefix of                                   |
   |           |'iso.org.dod.internet.private.enterprise' or          |
   |           |(1.3.6.1.4.1).                                        |
   |           |                                                      |
   |           |The PEC for each company can be found via a file at:  |
   |           |ftp://ftp.isi.edu/in-notes/iana/assignments/          |
   |           | enterprise-numbers                                   |
   |           |                                                      |
   |           |To encode the PEC for a vendor in each implementation |
   |           |of TALI, a 2 byte integer field is used.  The contents|
   |           |of the integer field should match the PEC code for    |
   |           |that company in the file mentioned above.             |
   |           |                                                      |
   |           |For example, Tekelec, which has a PEC of 323, will    |
   |           |code this 2 byte field as '0x0143'.                   |
   |           |                                                      |
   |           |Like other integer fields, the PEC value is           |
   |           |transmitted Least Significant Byte first across the   |
   |           |ethernet wire.                                        |
   +------------------------------------------------------------------+

   Table 10: Implementation for new field types introduced in TALI 2.0

4.5 Detailed TALI Message Structures for New 2.0 Opcodes

   The message structures for opcodes defined in version 1.0 of TALI are
   unchanged from the information presented earlier, with the exception
   of the 'moni' message.  The 2.0 format for the 'moni' message was
   described earlier.

   Detailed message structures, and discussion of the capabilities, for
   each of the new 2.0 opcodes is provided in the following sections.
   Before discussing each opcode individually, Table 11 provides the
   minimum and maximum value of the LENGTH field that should be
   supported for each new opcode (as well as 'moni/mona').  Table 11
   additionally shows the impact of ITU support that was added in 2.0.
   The routing label for ITU point codes only uses 4 octets instead of 7
   octets as ANSI requires.













Sprague, et al.              Informational                     [Page 59]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   +------------------------------------------------------------------+
   | Opcode | Valid Length | Comments                                 |
   |        | Field Values |                                          |
   +------------------------------------------------------------------+
   | moni   | 0-200 bytes  | The overall length of the data portion   |
   |        |              | for 'moni' on TALI 2.0 implementations   |
   |        |              | is unchanged from version 1.0 of the     |
   |        |              | specification and remains at 200 bytes   |
   |        |              | to provide backwards compatibility.      |
   +------------------------------------------------------------------+
   | mona   | 0-200 bytes  | The overall length of the data portion   |
   |        |              | for 'mona' on TALI 2.0 implementations   |
   |        |              | is unchanged from version 1.0 of the     |
   |        |              | specification and remains at 200 bytes   |
   |        |              | to provide backwards compatibility.      |
   +------------------------------------------------------------------+
   | mgmt   | 4-4096 bytes | The minimum length of 4 bytes is required|
   |        |              | to provide space for the Primitive field.|
   |        |              | The maximum length allows large TCP      |
   |        |              | packets to be supported if desired.      |
   +------------------------------------------------------------------+
   | xsrv   | 4-4096 bytes | The minimum length of 4 bytes is required|
   |        |              | to provide space for the Primitive field.|
   |        |              | The maximum length allows large TCP      |
   |        |              | packets to be supported if desired.      |
   +------------------------------------------------------------------+
   | spcl   | 4-4096 bytes | The minimum length of 4 bytes is required|
   |        |              | to provide space for the Primitive field.|
   |        |              | The maximum length allows large TCP      |
   |        |              | packets to be supported if desired.      |
   +------------------------------------------------------------------+
   | sccp   | 9-265 bytes  | These are the valid sizes for the        |
   |        |              | SCCP-ONLY portions of SCCP UDT MSUs.     |
   +------------------------------------------------------------------+
   | isot   | 8-273 bytes  | The length is the number of octets that  |
   |        |              | in the MTP3 and higher layer(s) of the   |
   |        |              | SS7 MSU.  This length includes the SIO   |
   |        |              | byte and all bytes in the SIF (Service   |
   |        |              | Information Field) field.  The MTP3      |
   |        |              | routing label is part of the SIF field.  |
   +------------------------------------------------------------------+
   | mtp3   | 8-280 bytes  | The length is the number of octets that  |
   |        |              | in the MTP3 and higher layer(s) of the   |
   |        |              | SS7 MSU.  This length includes the SIO   |
   |        |              | byte and all bytes in the SIF (Service   |
   |        |              | Information Field) field.  The MTP3      |
   |        |              | routing label is part of the SIF field.  |
   +------------------------------------------------------------------+



Sprague, et al.              Informational                     [Page 60]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   | saal   | 8-280 bytes  | The length is the number of octets that  |
   |        |              | in the MTP3 and higher layer(s) of the   |
   |        |              | SS7 MSU.  This length includes the SIO   |
   |        |              | byte and all bytes in the SIF (Service   |
   |        |              | Information Field) field.  The MTP3      |
   |        |              | routing label is part of the SIF field.  |
   |        |              | Seven (7) octets of SSCOP trailer is     |
   |        |              | added to the message.  The SSCOP trailer |
   |        |              | bytes are also included in the length.   |
   +------------------------------------------------------------------+

     Table 11: Valid Length Fields for Opcodes Affected by TALI 2.0

4.5.1 Management Message (mgmt)

   The 'mgmt' opcode is intended to allow Management data, or data that
   will manage the operation of the device, to pass between the TALI
   endpoints over the socket connection.  'mgmt' messages can be
   received and processed in any of the TALI NEx-FEx states.  Three
   PRIMITIVES are defined for use with this opcode:

   *  'rkrp' - Routing Key Registration Primitive.  This primitive
      allows the nodes to configure the SS7 traffic streams that they
      wish to receive over each socket.  This 'routing key registration'
      is performed in-band, via TALI messages.

   *  'mtpp' - MTP3 Primitives.  This primitive allows SS7 MTP3 network
      management messages regarding the (un)availability and congestion
      states of SS7 devices to be passed to the IP devices SG.

   *  'sorp' - Socket Options Registration Primitive.  This primitive
      allows various socket options to be enabled/disabled by each TALI
      device.

   As of version 2.0, the only defined primitives for the 'mgmt' opcode
   are 'rkrp', 'mtpp', and 'sorp'.  In the future, more primitives can
   be added to this opcode to extend the Management capabilities of the
   SG or IP devices.  The basic message structure for the 2.0 'mgmt'
   messages for all 3 of these primitives is as follows:












Sprague, et al.              Informational                     [Page 61]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   +------------------------------------------------------------------+
   | Octets | Field Name  | Description                               |
   +------------------------------------------------------------------+
   | 0..3   | SYNC        | 'TALI'                                    |
   +------------------------------------------------------------------+
   | 4..7   | OPCODE      | 'mgmt'                                    |
   +------------------------------------------------------------------+
   | 8..9   | LENGTH      | Length                                    |
   +------------------------------------------------------------------+
   | 10..13 | Primitive   | 'rkrp', 'mtpp' or 'sorp'  Each of these   |
   |        |             | primitives specify a group of applicable  |
   |        |             | management operations.                    |
   +------------------------------------------------------------------+
   | 14..17 | Primitive   | The operation field specifies the one     |
   |        | Operation   | operation within the group of operations  |
   |        |             | identified by the primitive.              |
   +------------------------------------------------------------------+
   | 18..   | Message     | The content of the message data area is   |
   |        | Data        | dependent on the combination of opcode/   |
   |        |             | primitive/operation fields.  Each of those|
   |        |             | combinations could use a different message|
   |        |             | data structure.                           |
   +------------------------------------------------------------------+

              Table 12: Message Structure for 'mgmt' opcode

4.5.1.1 Routing Key Registration Primitive (rkrp)

   The 'rkrp' primitive allows IP nodes to modify the application
   routing key table in the SG by sending TALI messages to configure the
   SS7 traffic streams that they wish to receive over each socket.  This
   'routing key registration' is performed in-band, via TALI messages,
   as an alternative to using the SG user interface to configure the
   routing keys.

   Recall from earlier discussion in this document that the
   specification supports five (5) types of fully specified routing
   keys:

   *  A key for SCCP traffic, where key = DPC-SI-SSN, where SI=3.

   *  A key for ISUP traffic, where key = DPC-SI-OPC-CIC Range, where
      SI=5.  The CIC values for traditional ISUP are 14 bit quantities
      in ANSI networks and 12 bit quantities in ITU networks.

   *  A key for TUP traffic, where key = DPC-SI-OPC-CIC Range, where
      SI=4.  This key is only supported for ITU networks.  The CIC
      values for TUP keys are 12 bit quantities in ITU networks.



Sprague, et al.              Informational                     [Page 62]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   *  A key for QBICC traffic (an extension of ISUP which uses 32 bit
      CIC codes), where key = DPC-SI-OPC-CIC, where SI=13.  The CIC
      values for QBICC keys are 32 bit quantities for ANSI and ITU
      networks.

   *  A key for OTHER-MTP3-SI (non-SCCP, non-ISUP, non-QBICC for ANSI
      and non-SCCP, non-ISUP, non-QBICC, non-TUP for ITU) traffic, where
      key = DPC-SI

   Each of these keys is fully specified key where the exact content of
   the MSU to be routed must match the data in the routing key.

   Extensions to the routing keys have been added that will support
   'partial match' or 'default' routing keys.  The purpose of these
   extensions is to improve the handling of MSU traffic when no fully
   specified routing key exists that matches the MSU.  Partial match and
   default routing keys are used when the SG can not find a fully
   specified routing key that can be used to route an MSU.  Partial
   match keys can be used to provide closest-match routing such as
   'ignore the CIC' for ISUP/QBICC/TUP traffic, or 'ignore the SSN' for
   SCCP traffic.  Default keys are used when no full or partial routing
   key has been  found as a last resort destination to route the MSU to.

   The types of partial and default keys defined by the protocol are
   discussed in the following table.  The 4th column in the table
   indicates the data structure that is used in the TALI rkrp message to
   perform operations on each partial/default key type.  Note: The order
   of the keys in the table (from top to bottom) matches the
   hierarchical search order that an SG will use to attempt to find a
   routing key to use for an MSU.  The partial and default keys are only
   used after attempting to find a fully specified key that matches the
   MSU.



















Sprague, et al.              Informational                     [Page 63]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   +--------+------------+--------------------------------+-----------+
   |Key     | Key        | Comments                       | Cross     |
   |Type    | Attributes |                                | Reference |
   +--------+------------+--------------------------------+-----------+
   |Partial | DPC-SI-OPC |Used as backup routes for CIC   | 4.5.1.1.2 |
   |        |            |based traffic (but ignoring the |           |
   |        |            |CIC field).                     |           |
   +--------+------------+--------------------------------+-----------+
   |Partial | DPC-SI     |Used as backup routes for CIC   | 4.5.1.1.4 |
   |        |            |based or SCCP traffic (but      |           |
   |        |            |ignoring the OPC-CIC or SSN).   |           |
   |        |            |Routes traffic based solely on  |           |
   |        |            |DPC and SI of the MSU.          |           |
   +--------+------------+--------------------------------+-----------+
   |Partial | DPC        |Used as a backup route for any  | 4.5.1.1.4 |
   |        |            |MSU type.  Routes traffic based |           |
   |        |            |solely on the DPC field.        |           |
   +--------+------------+--------------------------------+-----------+
   |Partial | SI         |Used as a backup route for any  | 4.5.1.1.4 |
   |        |            |MSU type.  Routes traffic based |           |
   |        |            |solely on the SI field.         |           |
   +--------+------------+--------------------------------+-----------+
   |Default | -          |If no other type of routing key | 4.5.1.1.5 |
   |        |            |for an MSU can be found, use    |           |
   |        |            |this one.                       |           |
   +--------+------------+--------------------------------+-----------+

    Table 13: Partial and Default Routing Keys (in hierarchical order)

   The specific capability requested in each 'rkrp' message is indicated
   via an 'RKRP Operation' field.  These capabilities include:

   *  ENTER: The ENTER operation creates an association between a
      specific socket and a specific application routing key.  The
      socket of the association is always the socket that the 'rkrp' was
      received on.  The application routing key identifies an SS7
      traffic stream that should be carried over that socket.  Multiple
      sockets can be associated with the same application routing key,
      if so, they all receive traffic in a 'load sharing' mode.  An
      override field can be used to remove any other socket associations
      for a particular routing key and add a single socket association.
      The ENTER operation is applicable for fully specified SCCP keys,
      CIC based keys (ISUP, Q.BICC, and TUP), OTHER-MTP3-SI keys, and
      all types of partial keys and to the default routing key.

   *  DELETE: The DELETE operation deletes an association between a
      specific socket and a specific application routing key.  The
      socket of the association is always the socket that the 'rkrp' was



Sprague, et al.              Informational                     [Page 64]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


      received on.  Other socket associations for the same application
      routing key are NOT affected by the deletion.  When the last
      socket association for a routing key is deleted, the entire
      routing key entry is removed from the database.  The DELETE
      operation operation is applicable for fully specified SCCP keys,
      CIC based keys (ISUP, Q.BICC, and  TUP), OTHER-MTP3-SI keys, and
      all types of partial keys and to the default routing key.

   *  SPLIT: The SPLIT operation is used to convert a single application
      routing key into 2 application routing keys that together cover
      the same SS7 traffic stream as the original key.  Immediately
      after a split is performed, both of the resulting entries retain
      the same socket associations as the original routing key.  When
      the split is completed, the socket associations can be modified
      for each of the 2 resulting ranges independent of the other range.
      The split operation is only applicable to fully specified CIC
      based keys (ISUP, QBICC, and TUP).  Each fully specified CIC based
      key is uniquely identified by the combination of DPC/SI/OPC/CIC
      range.  The CIC range is a continuous set of numbers from
      CICS(start) to CICE(end); the CIC range in the application routing
      key corresponds to the CIC value in a CIC based MSU.

   *  RESIZE: The RESIZE operation is used to modify the CIC range in
      for a single application routing key.  The resize operation is
      only applicable to fully specified CIC based routing keys.  The
      resize operation replaces the CICS/CICE values for a routing key
      with a new CIC range (NCICS/NCICE).  A wide variety of NCICS/NCICE
      ranges can be supported based on the existing CICS/CICE; just
      about the only restriction is that the new range can not already
      exist in the database and can not overlap any other entry in the
      database.  The socket associations for the routing key are NOT
      affected by the change in CICS/CICE.  The SPLIT operation is
      applicable only to fully specified CIC based keys (ISUP, Q.BICC,
      and TUP).

   The list of RKRP Operations (and their encodings) that are supported
   for TALI version 2.0 is as follows:

               0x0001 - ENTER ISUP KEY
               0x0002 - DELETE ISUP KEY
               0x0003 - SPLIT ISUP KEY
               0x0004 - RESIZE ISUP KEY
               0x0005 - ENTER Q.BICC ISUP KEY
               0x0006 - DELETE Q.BICC ISUP KEY
               0x0007 - SPLIT Q.BICC ISUP KEY
               0x0008 - RESIZE Q.BICC ISUP KEY
               0x0009 - ENTER SCCP KEY
               0x000A - DELETE SCCP KEY



Sprague, et al.              Informational                     [Page 65]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


               0x000B - ENTER OTHER-MTP3-SI KEY
               0x000C - DELETE OTHER-MTP3-SI KEY
               0x000D - ENTER TUP KEY (ITU only)
               0x000E - DELETE TUP KEY (ITU only)
               0x000F - SPLIT TUP KEY (ITU only)
               0x0010 - RESIZE TUP KEY (ITU only)
               0x0011 - ENTER DPC-SI-OPC PARTIAL KEY
               0x0012 - DELETE DPC-SI-OPC PARTIAL KEY
               0x0013 - ENTER DPC-SI PARTIAL KEY
               0x0014 - DELETE DPC-SI PARTIAL KEY
               0x0015 - ENTER DPC PARTIAL KEY
               0x0016 - DELETE DPC PARTIAL KEY
               0x0017 - ENTER SI PARTIAL KEY
               0x0018 - DELETE SI PARTIAL KEY
               0x0019 - ENTER DEFAULT
               0x001A - DELETE DEFAULT KEY
               0x001B - MULTIPLE REGISTRATION SUPPORT

   The message data area of the 'rkrp' messages will differ based on
   which RKRP Operation is specified.  Several different structures are
   used, the correct structure can be identified by the RKRP Operation
   field.

   In order to simplify the implementation, each of these structures
   will define a structure that will support all of the operations
   required for the key type.  This means that based on the rkrp
   operation, some of the fields will be required, and some of the
   fields will not be applicable for each RKRP message.  Unused fields
   should be initialized to 0 by the sender and ignored by the receiver.

4.5.1.1.1 RKRP Data Structures

4.5.1.1.1.1 Common Fields in all RKRP Messages

   In the following subsections several different data structures to be
   used for various RKRP operations are presented.  It should be noted
   that each of these data structures has the following fields in
   common.  The data structure below should begin at byte 14 of the TALI
   message as shown in Table 12.












Sprague, et al.              Informational                     [Page 66]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   +------------------------------------------------------------------+
   | Octets | Field Name  | Description                  | Field Type |
   +------------------------------------------------------------------+
   | 2      | RKRP        | Identifies which 'rkrp'      | Integer    |
   |        | Operation   | operation is desired.        |            |
   +------------------------------------------------------------------+
   | 2      | Request/    | Identifies whether the 'rkrp'| Integer    |
   |        | Reply       | message is a request (from an|            |
   |        |             | IP node to SG) for some type |            |
   |        |             | of 'rkrp' action, or a reply |            |
   |        |             | to a previous request (from  |            |
   |        |             | the SG back to the IP node). |            |
   |        |             | This integer field uses the  |            |
   |        |             | following encodings:         |            |
   |        |             | 0x0000=Request               |            |
   |        |             | 0x0001=Reply.  See Success/  |            |
   |        |             | Failure code for more info.  |            |
   +------------------------------------------------------------------+
   | 2      | Success/    | Provides a success/failure   | Integer    |
   |        | Failure     | indication as part of the    |            |
   |        | Code        | reply back to the IP node    |            |
   |        |             | for each processed request.  |            |
   |        |             | This field is only used when |            |
   |        |             | the Request/Reply field is   |            |
   |        |             | 0x0001.  This field uses the |            |
   |        |             | encodings from in section 5. |            |
   +------------------------------------------------------------------+

          Table 14: Common Fields in ALL 'rkrp' Data Structures

   The primary purpose of requiring the data structures for all RKRP
   operations to begin with these same fields, is to provide a means for
   a receiver to reply to unknown RKRP messages in a consistent manner.
   When an implementation receives an RKRP request message it does not
   understand, it should turn the request into a reply and use the
   success/failure code to indicate that the operation is not supported
   (with an RKRP Reply Code of Unsupported rkrp Operation).

   It is a requirement that these common fields continue to be used as
   new RKRP operations are added to this specification.  This will
   ensure that the capability described in the previous paragraph will
   always exist.









Sprague, et al.              Informational                     [Page 67]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


4.5.1.1.1.2 CIC Based Routing Key Operations

   The data structure used for 'rkrp' messages related to MSUs which are
   CIC based (ISUP, Q.BICC ISUP, and TUP (ITU only)) is as presented in
   the next table.  The data structure below should begin at byte 14 of
   the TALI message as shown in Table 12.

   Note 1: The number of bits used in each CIC field will vary based on
   the SI and network type.

   *  ISUP operations (0x0001 - 0x0004) are assumed to use 14 bit CIC
      values from the corresponding fields in the structure when DPC/OPC
      indicate an ANSI network (12 bits used in ITU networks).  Only the
      14(12) least significant bits of the 32 bit CIC field will be
      used.

   *  Q.BICC ISUP operations (0x0005 - 0x0008) are assumed to use 32 bit
      CIC values from the corresponding fields in the structure.

   *  TUP operations (0x000d - 0x0010) are assumed to use 12 bit CIC
      values from the corresponding fields in the structure when DPC/OPC
      indicate an ITU network.  Only the 12 least significant bits of
      the 32 bit CIC field will be used.   TUP operations are not
      supported for ANSI networks.

   Note 2: This same structure should be used to specify the partial key
   = DPC-SI-OPC(ignoreCIC).  When specifying a DPC-SI-OPC partial key,
   the CIC fields in this structure should be set to 0 by the sender.

   +------------------------------------------------------------------+
   | Octets | Field Name  | Description                  | Field Type |
   +------------------------------------------------------------------+
   | 2      | RKRP        | Identifies which 'rkrp'      | Integer    |
   |        | Operation   | operation is desired.        |            |
   +------------------------------------------------------------------+
   | 2      | Request/    | Identifies whether the 'rkrp'| Integer    |
   |        | Reply       | message is a request (from an|            |
   |        |             | IP node to SG) for some type |            |
   |        |             | of 'rkrp' action, or a reply |            |
   |        |             | to a previous request (from  |            |
   |        |             | the SG back to the IP node). |            |
   |        |             | This integer field uses the  |            |
   |        |             | following encodings:         |            |
   |        |             | 0x0000=Request               |            |
   |        |             | 0x0001=Reply.  See Success/  |            |
   |        |             | Failure code for more info.  |            |





Sprague, et al.              Informational                     [Page 68]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   +------------------------------------------------------------------+
   | 2      | Success/    | Provides a success/failure   | Integer    |
   |        | Failure     | indication as part of the    |            |
   |        | Code        | reply back to the IP node    |            |
   |        |             | for each processed request.  |            |
   |        |             | This field is only used when |            |
   |        |             | the Request/Reply field is   |            |
   |        |             | 0x0001.  This field uses the |            |
   |        |             | encodings listed in section  |            |
   |        |             | 5.                           |            |
   +------------------------------------------------------------------+
   | 2      | RKRP flags  | This is a 2 byte bit-field   | Bit-field  |
   |        |             | that provides 16 possible    |            |
   |        |             | flags that can control       |            |
   |        |             | various aspects of the       |            |
   |        |             | operation.                   |            |
   |        |             | Bit 0 - An Override bit is   |            |
   |        |             | used on the ENTER operation  |            |
   |        |             | to control how the socket    |            |
   |        |             | associations for a routing   |            |
   |        |             | key should be manipulated.   |            |
   |        |             | This flag determines if the  |            |
   |        |             | ENTER is to add the given    |            |
   |        |             | socket association in a      |            |
   |        |             | 'load-sharing' mode or if    |            |
   |        |             | the new association should   |            |
   |        |             | replace (Override) all       |            |
   |        |             | existing associations.  This |            |
   |        |             | flag is only examined on     |            |
   |        |             | ENTER operations.            |            |
   |        |             | Bit 0=0, Load Sharing Mode   |            |
   |        |             | Bit 0=1, Override Mode       |            |
   |        |             | Bits 1-15, currently         |            |
   |        |             | undefined                    |            |
   +------------------------------------------------------------------+
   | 1      | SI          | Service Indicator.  The SI   | Integer    |
   |        |             | field in an SS7 MSU          |            |
   |        |             | identifies the type of       |            |
   |        |             | traffic being carried by the |            |
   |        |             | MSU (0=SNM, 3=SCCP, 5=ISUP,  |            |
   |        |             | etc).  Each application      |            |
   |        |             | routing key must specify a   |            |
   |        |             | specific SI value that it    |            |
   |        |             | relates to.                  |            |
   |        |             | SI should be 5 for ISUP keys.|            |
   |        |             | SI should be 13 for Q.BICC   |            |
   |        |             | ISUP keys.                   |            |
   |        |             | SI should be 4 for TUP keys. |            |



Sprague, et al.              Informational                     [Page 69]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   +------------------------------------------------------------------+
   | 4      | DPC         | Destination Point Code.  Each| SS7 Point  |
   |        |             | SS7 MSU contains a DPC that  | Code       |
   |        |             | identifies the destination   |            |
   |        |             | for the MSU.  Each           |            |
   |        |             | application routing key must |            |
   |        |             | specify a specific DPC value |            |
   |        |             | that it relates to.          |            |
   +------------------------------------------------------------------+
   | 4      | OPC         | Origination Point Code.  Each| SS7 Point  |
   |        |             | SS7 MSU contains a OPC that  | Code       |
   |        |             | identifies the source of the |            |
   |        |             | MSU.  ISUP routing keys must |            |
   |        |             | each specify a single OPC    |            |
   |        |             | that the application routing |            |
   |        |             | key relates to.              |            |
   +------------------------------------------------------------------+
   | 4      | CICS        | Circuit Identification Code  | Integer    |
   |        |             | Start.  Each SS7 ISUP MSU    |            |
   |        |             | contains a CIC code.  Each   |            |
   |        |             | ISUP/QBICC/TUP routing key   |            |
   |        |             | identifies a range of CIC    |            |
   |        |             | values that are applicable   |            |
   |        |             | for the routing key.  The    |            |
   |        |             | CICS value is the low end of |            |
   |        |             | the CIC range.               |            |
   +------------------------------------------------------------------+
   | 4      | CICE        | Circuit Identification Code  | Integer    |
   |        |             | End.  Each SS7 ISUP MSU      |            |
   |        |             | contains a CIC code.  Each   |            |
   |        |             | ISUP/QBICC/TUP routing key   |            |
   |        |             | identifies a range of CIC    |            |
   |        |             | values that are applicable   |            |
   |        |             | for the routing key.  The    |            |
   |        |             | CICE value is the high end   |            |
   |        |             | of the CIC range.            |            |
   +------------------------------------------------------------------+
   | 4      | SPLIT CIC   | The SPLIT field is used on   | Integer    |
   |        |             | the SPLIT operation to       |            |
   |        |             | specify where in the existing|            |
   |        |             | CIC range (given by CICS/    |            |
   |        |             | CICE) an existing routing key|            |
   |        |             | should be split into 2       |            |
   |        |             | routing keys.  To be valid,  |            |
   |        |             | the following relationship   |            |
   |        |             | must be true before the SPLIT|            |
   |        |             | is performed:                |            |
   |        |             |    CICS < SPLIT <= CICE.     |            |



Sprague, et al.              Informational                     [Page 70]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   |        |             | After the SPLIT is performed,|            |
   |        |             | the 2 routing keys are as    |            |
   |        |             | follows:                     |            |
   |        |             |    CICS to SPLIT-1           |            |
   |        |             |    SPLIT to CICE             |            |
   +------------------------------------------------------------------+
   | 4      | NCICS       | The NCICS and NCICE fields   | Integer    |
   |        |             | are used on the RESIZE       |            |
   |        |             | operation to specify how the |            |
   |        |             | CIC range for existing       |            |
   |        |             | routing key should be        |            |
   |        |             | modified.  NCICS specifies   |            |
   |        |             | the new value that should    |            |
   |        |             | replace the existing CICS    |            |
   |        |             | value in the routing key.    |            |
   +------------------------------------------------------------------+
   | 4      | NCICE       | The NCICS and NCICE fields   | Integer    |
   |        |             | are used on the RESIZE       |            |
   |        |             | operation to specify how the |            |
   |        |             | CIC range for existing       |            |
   |        |             | routing key should be        |            |
   |        |             | modified.  NCICE specifies   |            |
   |        |             | the new value that should    |            |
   |        |             | replace the existing CICE    |            |
   |        |             | value in the routing key.    |            |
   +------------------------------------------------------------------+

    Table 15: Message Data Structure CIC based Routing Key Operations

   The following table indicates the Required (R), or Not Applicable
   (NA) status for each field of the message data structure in Table 15
   based on the RKRP Operation field.  As mentioned previously, unused
   fields (those marked NA) should be initialized to 0 by the sender and
   ignored by the receiver.

















Sprague, et al.              Informational                     [Page 71]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   +------------------------------------------------------------------+
   |      Operation  | ENTER | DELETE | SPLIT | RESIZE | ENTER/DELETE |
   |                 | (ISUP,| (ISUP, | (ISUP,| (ISUP, | PARTIAL DPC  |
   |                 | QBICC,| QBICC, | QBICC,| QBICC, | SI OPC KEY   |
   | Field           | TUP)  | TUP)   | TUP)  | TUP)   |              |
   +------------------------------------------------------------------+
   | Request/Reply   | R     | R      | R     | R      | R            |
   +------------------------------------------------------------------+
   | Success/Failure | R     | R      | R     | R      | R            |
   +------------------------------------------------------------------+
   | RKRP Flags      | R     | R      | R     | R      | R            |
   +------------------------------------------------------------------+
   | SI              | R     | R      | R     | R      | R            |
   +------------------------------------------------------------------+
   | DPC             | R     | R      | R     | R      | R            |
   +------------------------------------------------------------------+
   | OPC             | R     | R      | R     | R      | R            |
   +------------------------------------------------------------------+
   | CICS            | R     | R      | R     | R      | NA           |
   +------------------------------------------------------------------+
   | CICE            | R     | R      | R     | R      | NA           |
   +------------------------------------------------------------------+
   | SPLIT CIC       | NA    | NA     | R     | NA     | NA           |
   +------------------------------------------------------------------+
   | NCICS           | NA    | NA     | NA    | R      | NA           |
   +------------------------------------------------------------------+
   | NCICE           | NA    | NA     | NA    | R      | NA           |
   +------------------------------------------------------------------+

   Table 16: Required/Not Applicable Fields for CIC based Routing Keys

4.5.1.1.1.3 SCCP Routing Key Operations

   The data structure used for 'rkrp' messages related to SCCP routing
   keys is presented in the next table.  The data structure below should
   begin at byte 14 of the TALI message as shown in Table 12.















Sprague, et al.              Informational                     [Page 72]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   +------------------------------------------------------------------+
   | Octets | Field Name  | Description                  | Field Type |
   +------------------------------------------------------------------+
   | 2      | RKRP        | Identifies which 'rkrp'      | Integer    |
   |        | Operation   | operation is desired.        |            |
   +------------------------------------------------------------------+
   | 2      | Request/    | Identifies whether the 'rkrp'| Integer    |
   |        | Reply       | message is a request (from an|            |
   |        |             | IP node to SG) for some type |            |
   |        |             | of 'rkrp' action, or a reply |            |
   |        |             | to a previous request (from  |            |
   |        |             | the SG back to the IP node). |            |
   |        |             | This integer field uses the  |            |
   |        |             | following encodings:         |            |
   |        |             | 0x0000=Request               |            |
   |        |             | 0x0001=Reply.  See Success/  |            |
   |        |             | Failure code for more info.  |            |
   +------------------------------------------------------------------+
   | 2      | Success/    | Provides a success/failure   | Integer    |
   |        | Failure     | indication as part of the    |            |
   |        | Code        | reply back to the IP node    |            |
   |        |             | for each processed request.  |            |
   |        |             | This field is only used when |            |
   |        |             | the Request/Reply field is   |            |
   |        |             | 0x0001.  This field uses the |            |
   |        |             | encodings listed in section  |            |
   |        |             | 5.                           |            |
   +------------------------------------------------------------------+
   | 2      | RKRP flags  | This is a 2 byte bit-field   | Bit-field  |
   |        |             | that provides 16 possible    |            |
   |        |             | flags that can control       |            |
   |        |             | various aspects of the       |            |
   |        |             | operation.                   |            |
   |        |             | Bit 0 - An Override bit is   |            |
   |        |             | used on the ENTER operation  |            |
   |        |             | to control how the socket    |            |
   |        |             | associations for a routing   |            |
   |        |             | key should be manipulated.   |            |
   |        |             | This flag determines if the  |            |
   |        |             | ENTER is to add the given    |            |
   |        |             | socket association in a      |            |
   |        |             | 'load-sharing' mode or if    |            |
   |        |             | the new association should   |            |
   |        |             | replace (Override) all       |            |
   |        |             | existing associations.  This |            |
   |        |             | flag is only examined on     |            |
   |        |             | ENTER operations.            |            |
   |        |             | Bit 0=0, Load Sharing Mode   |            |



Sprague, et al.              Informational                     [Page 73]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   |        |             | Bit 0=1, Override Mode       |            |
   |        |             | Bits 1-15, currently         |            |
   |        |             | undefined                    |            |
   +------------------------------------------------------------------+
   | 1      | SI          | Service Indicator.  The SI   | Integer    |
   |        |             | field in an SS7 MSU          |            |
   |        |             | identifies the type of       |            |
   |        |             | traffic being carried by the |            |
   |        |             | MSU (0=SNM, 3=SCCP, 5=ISUP,  |            |
   |        |             | etc).  Each application      |            |
   |        |             | routing key must specify a   |            |
   |        |             | specific SI value that it    |            |
   |        |             | relates to.                  |            |
   |        |             | SI should be 3 for SCCP keys.|            |
   +------------------------------------------------------------------+
   | 4      | DPC         | Destination Point Code.  Each| SS7 Point  |
   |        |             | SS7 MSU contains a DPC that  | Code       |
   |        |             | identifies the destination   |            |
   |        |             | for the MSU.  Each           |            |
   |        |             | application routing key must |            |
   |        |             | specify a specific DPC value |            |
   |        |             | that it relates to.          |            |
   +------------------------------------------------------------------+
   | 1      | SSN         | SubSystem Number.  Each SCCP | Integer    |
   |        |             | MSU contains a subsystem     |            |
   |        |             | number that identifies the   |            |
   |        |             | SCCP subsystem that should   |            |
   |        |             | process the MSU.  SCCP       |            |
   |        |             | routing keys must each       |            |
   |        |             | specify a single SSN that    |            |
   |        |             | the application routing key  |            |
   |        |             | relates to.                  |            |
   +------------------------------------------------------------------+

      Table 17: Message Data Structure SCCP Routing Key Operations

   The following table indicates the Required (R), or Not Applicable
   (NA) status for each field of the message data structure in Table 17
   based on the RKRP Operation field.  As mentioned previously, unused
   fields (those marked NA) should be initialized to 0 by the sender and
   ignored by the receiver.










Sprague, et al.              Informational                     [Page 74]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


              +--------------------------------------------+
              |      Operation  | ENTER SCCP | DELETE SCCP |
              | Field           |            |             |
              +--------------------------------------------+
              | Request/Reply   | R          | R           |
              +--------------------------------------------+
              | Success/Failure | R          | R           |
              +--------------------------------------------+
              | RKRP Flags      | R          | R           |
              +--------------------------------------------+
              | SI              | R          | R           |
              +--------------------------------------------+
              | DPC             | R          | R           |
              +--------------------------------------------+
              | SSN             | R          | R           |
              +--------------------------------------------+

      Table 18: Required/Not Applicable Fields for SCCP Routing Keys

4.5.1.1.1.4 DPC-SI, DPC and SI based Routing Key Operations

   The data structure used for 'rkrp' messages related to DPC-SI based
   (either full keys for non-sccp, non-cic based traffic, or partial
   keys for CIC based or SCCP), DPC based (partial key), and SI based
   (partial key) operations is as presented in the next table.  The data
   structure below should begin at byte 14 of the TALI message as shown
   in Table 12.

   +------------------------------------------------------------------+
   | Octets | Field Name  | Description                  | Field Type |
   +------------------------------------------------------------------+
   | 2      | RKRP        | Identifies which 'rkrp'      | Integer    |
   |        | Operation   | operation is desired.        |            |
   +------------------------------------------------------------------+
   | 2      | Request/    | Identifies whether the 'rkrp'| Integer    |
   |        | Reply       | message is a request (from an|            |
   |        |             | IP node to SG) for some type |            |
   |        |             | of 'rkrp' action, or a reply |            |
   |        |             | to a previous request (from  |            |
   |        |             | the SG back to the IP node). |            |
   |        |             | This integer field uses the  |            |
   |        |             | following encodings:         |            |
   |        |             | 0x0000=Request               |            |
   |        |             | 0x0001=Reply.  See Success/  |            |
   |        |             | Failure code for more info.  |            |






Sprague, et al.              Informational                     [Page 75]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   +------------------------------------------------------------------+
   | 2      | Success/    | Provides a success/failure   | Integer    |
   |        | Failure     | indication as part of the    |            |
   |        | Code        | reply back to the IP node    |            |
   |        |             | for each processed request.  |            |
   |        |             | This field is only used when |            |
   |        |             | the Request/Reply field is   |            |
   |        |             | 0x0001.  This field uses the |            |
   |        |             | encodings from section 5.    |            |
   +------------------------------------------------------------------+
   | 2      | RKRP flags  | This is a 2 byte bit-field   | Bit-field  |
   |        |             | that provides 16 possible    |            |
   |        |             | flags that can control       |            |
   |        |             | various aspects of the       |            |
   |        |             | operation.                   |            |
   |        |             | Bit 0 - An Override bit is   |            |
   |        |             | used on the ENTER operation  |            |
   |        |             | to control how the socket    |            |
   |        |             | associations for a routing   |            |
   |        |             | key should be manipulated.   |            |
   |        |             | This flag determines if the  |            |
   |        |             | ENTER is to add the given    |            |
   |        |             | socket association in a      |            |
   |        |             | 'load-sharing' mode or if    |            |
   |        |             | the new association should   |            |
   |        |             | replace (Override) all       |            |
   |        |             | existing associations.  This |            |
   |        |             | flag is only examined on     |            |
   |        |             | ENTER operations.            |            |
   |        |             | Bit 0=0, Load Sharing Mode   |            |
   |        |             | Bit 0=1, Override Mode       |            |
   |        |             | Bits 1-15, currently         |            |
   |        |             | undefined                    |            |
   +------------------------------------------------------------------+
   | 1      | SI          | Service Indicator.  The SI   | Integer    |
   |        |             | field in an SS7 MSU          |            |
   |        |             | identifies the type of       |            |
   |        |             | traffic being carried by the |            |
   |        |             | MSU (0=SNM, 3=SCCP, 5=ISUP,  |            |
   |        |             | etc).  Each application      |            |
   |        |             | routing key must specify a   |            |
   |        |             | specific SI value that it    |            |
   |        |             | relates to.                  |            |
   +------------------------------------------------------------------+







Sprague, et al.              Informational                     [Page 76]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   | 4      | DPC         | Destination Point Code.  Each| SS7 Point  |
   |        |             | SS7 MSU contains a DPC that  | Code       |
   |        |             | identifies the destination   |            |
   |        |             | for the MSU.  Each           |            |
   |        |             | application routing key must |            |
   |        |             | specify a specific DPC value |            |
   |        |             | that it relates to.          |            |
   +------------------------------------------------------------------+
   Table 19: Message Data Structure DPC/SI, DPC and SI based Routing
             Key Operations

   The following table indicates the Required (R), or Not Applicable
   (NA) status for each field of the message data structure in Table 19
   based on the RKRP Operation field.  As mentioned previously, unused
   fields (those marked NA) should be initialized to 0 by the sender and
   ignored by the receiver.

         +-------------------------------------------------------+
         |      Operation  | ENTER/  | ENTER/  | ENTER/ | ENTER/ |
         |                 | DELETE  | DELETE  | DELETE | DELETE |
         |                 | OTHER   | DPC-SI  | DPC    | SI     |
         | Field           | MTP3 SI | PARTIAL | ONLY   | ONLY   |
         +-------------------------------------------------------+
         | Request/Reply   | R       | R       | R      | R      |
         +-------------------------------------------------------+
         | Success/Failure | R       | R       | R      | R      |
         +-------------------------------------------------------+
         | RKRP Flags      | R       | R       | R      | R      |
         +-------------------------------------------------------+
         | SI              | R       | R       | NA     | R      |
         +-------------------------------------------------------+
         | DPC             | R       | R       | R      | NA     |
         +-------------------------------------------------------+

         Table 20: Required/Not Applicable Fields for DPC/SI, DPC
                   and SI based Routing Keys

4.5.1.1.1.5 Default Routing Key Operations

   The data structure used for 'rkrp' messages related to entering and
   deleting a default routing key is as presented in the next table.
   The data structure below should begin at byte 14 of the TALI message
   as shown in Table 12.








Sprague, et al.              Informational                     [Page 77]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   +------------------------------------------------------------------+
   | Octets | Field Name  | Description                  | Field Type |
   +------------------------------------------------------------------+
   | 2      | RKRP        | Identifies which 'rkrp'      | Integer    |
   |        | Operation   | operation is desired.        |            |
   +------------------------------------------------------------------+
   | 2      | Request/    | Identifies whether the 'rkrp'| Integer    |
   |        | Reply       | message is a request (from an|            |
   |        |             | IP node to SG) for some type |            |
   |        |             | of 'rkrp' action, or a reply |            |
   |        |             | to a previous request (from  |            |
   |        |             | the SG back to the IP node). |            |
   |        |             | This integer field uses the  |            |
   |        |             | following encodings:         |            |
   |        |             | 0x0000=Request               |            |
   |        |             | 0x0001=Reply.  See Success/  |            |
   |        |             | Failure code for more info.  |            |
   +------------------------------------------------------------------+
   | 2      | Success/    | Provides a success/failure   | Integer    |
   |        | Failure     | indication as part of the    |            |
   |        | Code        | reply back to the IP node    |            |
   |        |             | for each processed request.  |            |
   |        |             | This field is only used when |            |
   |        |             | the Request/Reply field is   |            |
   |        |             | 0x0001.  This field uses the |            |
   |        |             | encodings listed in section  |            |
   |        |             | 5.                           |            |
   +------------------------------------------------------------------+
   | 2      | RKRP flags  | This is a 2 byte bit-field   | Bit-field  |
   |        |             | that provides 16 possible    |            |
   |        |             | flags that can control       |            |
   |        |             | various aspects of the       |            |
   |        |             | operation.                   |            |
   |        |             | Bit 0 - An Override bit is   |            |
   |        |             | used on the ENTER operation  |            |
   |        |             | to control how the socket    |            |
   |        |             | associations for a routing   |            |
   |        |             | key should be manipulated.   |            |
   |        |             | This flag determines if the  |            |
   |        |             | ENTER is to add the given    |            |
   |        |             | socket association in a      |            |
   |        |             | 'load-sharing' mode or if    |            |
   |        |             | the new association should   |            |
   |        |             | replace (Override) all       |            |
   |        |             | existing associations.  This |            |
   |        |             | flag is only examined on     |            |
   |        |             | ENTER operations.            |            |
   |        |             | Bit 0=0, Load Sharing Mode   |            |



Sprague, et al.              Informational                     [Page 78]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   |        |             | Bit 0=1, Override Mode       |            |
   |        |             | Bits 1-15, currently         |            |
   |        |             | undefined                    |            |
   +------------------------------------------------------------------+

        Table 21: Message Data Structure for Default Routing Keys

   The following table indicates the Required (R), or Not Applicable
   (NA) status for each field of the message data structure in Table 21
   based on the RKRP Operation field.  As mentioned previously, unused
   fields (those marked NA) should be initialized to 0 by the sender and
   ignored by the receiver.

              +-------------------------------------+
              |      Operation  | ENTER   | DELETE  |
              | Field           | DEFAULT | DEFAULT |
              +-------------------------------------+
              | Request/Reply   | R       | R       |
              +-------------------------------------+
              | Success/Failure | R       | R       |
              +-------------------------------------+
              | RKRP Flags      | R       | R       |
              +-------------------------------------+

      Table 22: Required/Not Applicable Fields for Default Routing Keys

4.5.1.1.1.6 Support for Multiple RKRP Registration Operations

   The intent of support for multiple RKRP operations within a single
   TALI message (opcode = 'mgmt', primitive = 'rkrp') is to decrease the
   message count and byte overhead on network transmission when
   performing massive registration sequences.

   This functionality is added by 2 mechanisms:

   *  a new RKRP operation (0X001B, MULTIPLE REGISTRATIONS SUPPORT) is
      defined.  This operation is meant to be used in a query/reply
      manner to determine if the far end supports multiple RKRP
      registrations per TALI message before using such capability.

   *  The basic 'rkrp' message structure is extended to allow multiple
      rkrp operations to follow one another in a tali message.

4.5.1.1.1.6.1 Multiple Registrations Support

   A new RKRP operation and accompanying data structure are defined to
   determine if a far end device supports multiple RKRP registration
   operations per TALI message.



Sprague, et al.              Informational                     [Page 79]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   The data structure used for the 'multiple registrations support'
   operation is as presented in the next table.  The data structure
   below should begin at byte 14 of the TALI message as shown in Table
   12.

   +------------------------------------------------------------------+
   | Octets | Field Name  | Description                  | Field Type |
   +------------------------------------------------------------------+
   | 2      | RKRP        | Identifies which 'rkrp'      | Integer    |
   |        | Operation   | operation is desired.        |            |
   +------------------------------------------------------------------+
   | 2      | Request/    | Identifies whether the 'rkrp'| Integer    |
   |        | Reply       | message is a request (from an|            |
   |        |             | IP node to SG) for some type |            |
   |        |             | of 'rkrp' action, or a reply |            |
   |        |             | to a previous request (from  |            |
   |        |             | the SG back to the IP node). |            |
   |        |             | This integer field uses the  |            |
   |        |             | following encodings:         |            |
   |        |             | 0x0000=Request               |            |
   |        |             | 0x0001=Reply.  See Success/  |            |
   |        |             | Failure code for more info.  |            |
   +------------------------------------------------------------------+
   | 2      | Success/    | Provides a success/failure   | Integer    |
   |        | Failure     | indication as part of the    |            |
   |        | Code        | reply back to the IP node    |            |
   |        |             | for each processed request.  |            |
   |        |             | This field is only used when |            |
   |        |             | the Request/Reply field is   |            |
   |        |             | 0x0001.  This field uses the |            |
   |        |             | encodings listed in section  |            |
   |        |             | 5.                           |            |
   +------------------------------------------------------------------+
   | 4      | Operations  | This field is used by the    | Integer    |
   |        | Per Message | reply to tell the requester  |            |
   |        |             | the maximum # of RKRP        |            |
   |        |             | registration operations per  |            |
   |        |             | TALI message that are        |            |
   |        |             | supported by the             |            |
   |        |             | implementation.              |            |
   |        |             | * This field should be set   |            |
   |        |             |   to 0 when the request/     |            |
   |        |             |   reply field is set to      |            |
   |        |             |   Request.                   |            |
   |        |             | * This field should be set to|            |
   |        |             |   the Maximum # of operations|            |
   |        |             |   per TALI message that a    |            |
   |        |             |   TALI implementation is     |            |



Sprague, et al.              Informational                     [Page 80]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   |        |             |   willing to support when the|            |
   |        |             |   request/reply field is set |            |
   |        |             |   to Reply.                  |            |
   +------------------------------------------------------------------+
    Table 23: Message Data Structure for Multiple Registrations Support
              Operation

   The following table indicates the Required (R), or Not Applicable
   (NA) status for each field of the message data structure above.  As
   mentioned previously, unused fields (those marked NA) should be
   initialized to 0 by the sender and ignored by the receiver.

           +-------------------------------------------------+
           |      Operation  | MULTIPLE      | MULTIPLE      |
           |                 | REGISTRATIONS | REGISTRATIONS |
           |                 | SUPPORT       | SUPPORT       |
           | Field           | REQUEST       | REPLY         |
           +-------------------------------------------------+
           | Request/Reply   | R             | R             |
           +-------------------------------------------------+
           | Success/Failure | R             | R             |
           +-------------------------------------------------+
           | Operations Per  | R             | R             |
           | Message         |               |               |
           +-------------------------------------------------+

    Table 24: Required/Not Applicable Fields for Multiple Registrations
              Support Operation

4.5.1.1.1.6.2 Multiple RKRP Operations in a Single Message

   After using the MULTIPLE REGISTRATIONS SUPPORT operation to determine
   that the far end supports multiple RKRP operations per TALI message,
   a device wishing to use this functionality can begin sending more
   than 1 registration request/reply per message.  To do so, the basic
   message structure for an 'mgmt' opcode (presented in Table 12) can be
   extended so that each operation directly follows the previous
   operation in the TALI message.  An example showing a TALI message
   with 3 RKRP operations in it would look as follows:












Sprague, et al.              Informational                     [Page 81]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   +------------------------------------------------------------------+
   | Octets | Field Name  | Description                               |
   +------------------------------------------------------------------+
   | 0..3   | SYNC        | 'TALI'                                    |
   +------------------------------------------------------------------+
   | 4..7   | OPCODE      | 'mgmt'                                    |
   +------------------------------------------------------------------+
   | 8..9   | LENGTH      | Length. The length should be set such that|
   |        |             | all (3 in this example) operations are    |
   |        |             | accounted for.                            |
   +------------------------------------------------------------------+
   | 10..13 | Primitive   | 'rkrp'                                    |
   +------------------------------------------------------------------+
   | 14..17 | Primitive   | The fisrt operation field identifies a    |
   |        | Operation   | specific rkrp operation to be performed.  |
   |        | #1          |                                           |
   +------------------------------------------------------------------+
   | 18..x  | Message     | The length of the message data (and the   |
   |        | Data for    | interpretation of those bytes) for        |
   |        | Operation   | operation #1 depends on the message data  |
   |        | #1          | required for rkrp operation #1            |
   +------------------------------------------------------------------+
   | x+1..  | Primitive   | The fisrt operation field identifies a    |
   |   x+4  | Operation   | specific rkrp operation to be performed.  |
   |        | #2          |                                           |
   +------------------------------------------------------------------+
   | x+5..y | Message     | The length of the message data (and the   |
   |        | Data for    | interpretation of those bytes) for        |
   |        | Operation   | operation #2 depends on the message data  |
   |        | #2          | required for rkrp operation #2            |
   +------------------------------------------------------------------+
   | y+1..  | Primitive   | The fisrt operation field identifies a    |
   |   y+4  | Operation   | specific rkrp operation to be performed.  |
   |        | #3          |                                           |
   +------------------------------------------------------------------+
   | y+5..z | Message     | The length of the message data (and the   |
   |        | Data for    | interpretation of those bytes) for        |
   |        | Operation   | operation #3 depends on the message data  |
   |        | #3          | required for rkrp operation #3            |
   +------------------------------------------------------------------+

      Table 25: Message Structure for 'mgmt' opcode with multiple
                'rkrp' operations in 1 TALI Message








Sprague, et al.              Informational                     [Page 82]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   It should be reiterated that in order to avoid unpredictable
   behavior, a node using the 'multiple registrations per TALI msg'
   capability must be sure the far end device supports the capability.
   The only way to be sure of this is to successfully send a MULTIPLE
   REGISTRATION SUPPORT request and receive a MULTIPLE REGISTRATION
   SUPPORT reply.

4.5.1.2 MTP3 Primitive (mtpp)

   The 'mtpp' primitive allows IP nodes to receive status regarding
   point code (un)availability and congestion levels.  These messages
   provide information similar to the TFP/TFA (TransFer Prohibited and
   TransFer Allowed), TFC (TransFer Congested) and RCT (Route Congestion
   Test) messages that are encoded as SS7 SNM (Signaling Network
   Management) MSUs in traditional SS7 networks.  The 'mtp3 primitives'
   allow this status information to be transferred in-band, via TALI
   messages, to the IP nodes.

   The specific information provided in each 'mtpp' message is indicated
   via an 'MTPP Operation' field.  These capabilities provided by the
   various MTPP Operation fields include:

   *  POINT CODE UNAVAILABLE: This primitive operation announces that an
      SS7 Point Code is Unavailable (ie: the SG has NO route available
      to send traffic for the destination).  The PT CODE field indicates
      which SS7 Pt Code this operation is concerned with.

   *  POINT CODE AVAILABLE: This primitive operation announces that an
      SS7 Point Code is Available (ie: the SG has SOME route available
      to send traffic for the destination).  The PT CODE field indicates
      which SS7 Pt Code this operation is concerned with.

   *  REQUEST FOR POINT CODE STATUS: This primitive operation provides a
      way for one end of the connection to poll the other end for the
      available/unavailable status of a specific SS7 pt code.  For
      instance, the IP node can poll the SG - Can you send traffic
      successfully for the destination indicated?  The receiver of the
      request will reply to the request with either a point code
      available or pt code unavailable primitive respectively.

   *  CLUSTER UNAVAILABLE: This primitive operation announces that an
      entire Cluster of SS7 Point Codes (ex: 10-10-*) are Unavailable
      (ie: the SG has NO route available to send traffic for any of the
      destinations in that cluster).  The PT CODE field indicates which
      SS7 Cluster Pt Code this operation is concerned with.

   *  CLUSTER AVAILABLE: This primitive operation announces that at
      least 1 SS7 Point Code within a cluster is Available (ie: the SG



Sprague, et al.              Informational                     [Page 83]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


      has SOME route available to send traffic for at least 1 of the
      destinations in that cluster).  The PT CODE field indicates which
      SS7 Cluster Pt Code this operation is concerned with.

   *  REQUEST FOR CLUSTER STATUS: This primitive operation provides a
      way for one end of the connection to poll the other end for the
      available/unavailable status of a cluster of SS7 pt codes.  For
      instance, the IP node can poll the SG - Can you send traffic
      successfully for any of the destinations in the cluster?  The
      receiver of the request will reply to the request with either a
      cluster available or cluster unavailable primitive respectively.

   *  CONGESTED DESTINATION: This primitive operation announces that the
      path towards an SS7 Point Code is Congested.  The PT CODE field
      indicates which SS7 Pt Code this operation is concerned with.  The
      CONGESTION LEVEL field indicates the severity of the congestion.

   *  REQUEST FOR CONGESTION STATUS: This primitive operation provides a
      way for one end of the connection to poll the other end for the
      congestion status of an SS7 pt code.  For instance, the IP node
      can poll the SG - Is the path to the specified destination still
      congested?  This request is used to abate congestion towards an
      SS7 destination.

      *  As an implementation note: Upon receiving this request, the SG
         will generate and send a Route Congestion Test (RCT), SS7
         Network Management Message with a priority set to match the
         congestion level in the request.  The RCT is sent towards the
         SS7 destination.  If the SS7 destination is still congested,
         the RCT will result an SS7 Transfer Controlled (TFC) arriving
         back at the SG, which will be converted into a CONGESTED
         DESTINATION primitive and sent on to the IP node.

   *  USER PART UNAVAILABLE: SS7 nodes send User Part Unavailable
      messages when a user part that is mounted on a node is no longer
      available for service.  This primitive operation provides a way
      for an IP Node to receive the same information as the SS7 UPU
      message.

   In order to simplify the implementation, a single data structure is
   defined to be used for all of the 'mtpp' operations.  Depending on
   the 'mtpp operation', some of the fields will be required, and some
   of the fields will not be applicable for each MTPP message.  Unused
   fields should be initialized to 0 by the sender and ignored by the
   receiver.  The data structure used for 'mtpp' messages is as
   presented in the next table.  The data structure below should begin
   at byte 14 of the TALI message as shown in Table 12.




Sprague, et al.              Informational                     [Page 84]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   +------------------------------------------------------------------+
   | Octets | Field Name  | Description                  | Field Type |
   +------------------------------------------------------------------+
   | 2      | MTPP        | Identifies which 'mtpp'      | Integer    |
   |        | Operation   | operation/capability is      |            |
   |        |             | provided in this message.    |            |
   |        |             | This integer field uses the  |            |
   |        |             | following encodings:         |            |
   |        |             | 0x0001 = PC Unavailable      |            |
   |        |             | 0x0002 = PC Available        |            |
   |        |             | 0x0003 = Request for PC      |            |
   |        |             |          Status              |            |
   |        |             | 0x0004 = Cluster Unavailable |            |
   |        |             | 0x0005 = Cluster Available   |            |
   |        |             | 0x0006 = Request for Cluster |            |
   |        |             |          Status              |            |
   |        |             | 0x0007 = Congested           |            |
   |        |             |          Destination, w/Cong |            |
   |        |             |          Level               |            |
   |        |             | 0x0008 = Request for         |            |
   |        |             |          Congestion Status   |            |
   |        |             | 0x0009 = User Part           |            |
   |        |             |          Unavailable         |            |
   +------------------------------------------------------------------+
   | 4      | Concerned   | Identifies the SS7 Point Code| SS7 Point  |
   |        | Point       | that is relevant to the mtpp | Code       |
   |        | Code        | operation.  The mtpp         |            |
   |        |             | operation is concerning this |            |
   |        |             | point code (or cluster).     |            |
   +------------------------------------------------------------------+
   | 4      | Source      | This field is only used on   | SS7 Point  |
   |        | Point       | the 'Congested Destination'  | Code       |
   |        | Code        | and 'Request for Congestion  |            |
   |        |             | Status' operations.          |            |
   |        |             | * When used in an 'Congestion|            |
   |        |             |   Destination' operation,    |            |
   |        |             |   this field contains the Pt |            |
   |        |             |   Code of the Source of the  |            |
   |        |             |   traffic that was           |            |
   |        |             |   experiencing congestion as |            |
   |        |             |   it made its way to the     |            |
   |        |             |   Concerned Pt Code.  In     |            |
   |        |             |   terms of the original SS7  |            |
   |        |             |   MSUs (the TransFer         |            |
   |        |             |   Controlled MSU) that       |            |
   |        |             |   provided congestion        |            |
   |        |             |   information, the CPC of the|            |
   |        |             |   TFC is the 'Concerned Point|            |



Sprague, et al.              Informational                     [Page 85]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   |        |             |   Code' of the resulting MTPP|            |
   |        |             |   primitive and the DPC of   |            |
   |        |             |   the TFC is the 'Source     |            |
   |        |             |   Point Code' of the         |            |
   |        |             |   resulting MTPP primitive.  |            |
   |        |             | * When used in an 'Request   |            |
   |        |             |   for Congestion Status'     |            |
   |        |             |   operation, this field      |            |
   |        |             |   indicates which Source Pt  |            |
   |        |             |   Code is trying to abate the|            |
   |        |             |   congestion of the concerned|            |
   |        |             |   Pt Code.  In terms of the  |            |
   |        |             |   original SS7 MSUs (the     |            |
   |        |             |   Route Congestion Test MSU) |            |
   |        |             |   that is used to poll for   |            |
   |        |             |   congestion, the DPC of the |            |
   |        |             |   RCT is the 'Concerned Point|            |
   |        |             |   Code' of the MTPP primitive|            |
   |        |             |   and the OPC of the RCT is  |            |
   |        |             |   the 'Source Point Code' of |            |
   |        |             |   the MTPP primitive.        |            |
   +------------------------------------------------------------------+
   | 2      | Congestion  | This field is used on the    | Integer    |
   |        | Level       | 'Congested Destination' and  |            |
   |        |             | 'Request for Congestion      |            |
   |        |             | Status' operations to        |            |
   |        |             | indicate the congestion level|            |
   |        |             | of the destination.  This    |            |
   |        |             | integer field uses the       |            |
   |        |             | following encodings:         |            |
   |        |             | 0x0000 = Congestion Level 0  |            |
   |        |             | 0x0001 = Congestion Level 1  |            |
   |        |             | 0x0002 = Congestion Level 2  |            |
   |        |             | 0x0003 = Congestion Level 3  |            |
   +------------------------------------------------------------------+
   | 2      | Cause Code  | This field is used on the    | Integer    |
   |        |             | 'User Part Unavailable'      |            |
   |        |             | operation to indicate the    |            |
   |        |             | Cause Code for why the UPU is|            |
   |        |             | being sent.  This integer    |            |
   |        |             | field uses the following     |            |
   |        |             | encodings:                   |            |
   |        |             | 0x0000 = Cause Unknown       |            |
   |        |             | 0x0001 = User Part Unequipped|            |
   |        |             | 0x0002 = User Part           |            |
   |        |             |          Inaccessible        |            |
   +------------------------------------------------------------------+




Sprague, et al.              Informational                     [Page 86]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   | 2      | User ID     | This field is used on the    | Integer    |
   |        |             | 'User Part Unavailable'      |            |
   |        |             | operation to indicate which  |            |
   |        |             | user part is unavailable. The|            |
   |        |             | User ID field identifies the |            |
   |        |             | type of traffic that was     |            |
   |        |             | unavailable (0=SNM, 3=SCCP,  |            |
   |        |             | 5=ISUP, etc).                |            |
   +------------------------------------------------------------------+

    Table 26: Message Data Structure for use with the 'mtpp' Primitive

   The following table indicates the Required (R), or Not Applicable
   (NA) status for each field of the message data structure in Table 26
   based on the MTPP Operation field.  As mentioned previously, unused
   fields (those marked NA) should be initialized to 0 by the sender and
   ignored by the receiver.


































Sprague, et al.              Informational                     [Page 87]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   +------------------------------------------------------------------+
   |          Field  | Concerned | Source | Congestion | Cause | User |
   |                 | Point     | Point  |  Level     | Code  | ID   |
   | Operation       | Code      | Code   |            |       |      |
   +------------------------------------------------------------------+
   | PC Unavailable  | R         | NA     | NA         | NA    | NA   |
   +------------------------------------------------------------------+
   | PC Available    | R         | NA     | NA         | NA    | NA   |
   +------------------------------------------------------------------+
   | Request for PC  | R         | NA     | NA         | NA    | NA   |
   | Status          |           |        |            |       |      |
   +------------------------------------------------------------------+
   | Cluster         | R         | NA     | NA         | NA    | NA   |
   | Unavailable     |           |        |            |       |      |
   +------------------------------------------------------------------+
   | Cluster         | R         | NA     | NA         | NA    | NA   |
   | Available       |           |        |            |       |      |
   +------------------------------------------------------------------+
   | Request for     | R         | NA     | NA         | NA    | NA   |
   | Cluster Status  |           |        |            |       |      |
   +------------------------------------------------------------------+
   | Congested       |           |        |            |       |      |
   | Destination w/  | R         | R      | R          | NA    | NA   |
   | Cong. Level     |           |        |            |       |      |
   +------------------------------------------------------------------+
   | Request for     |           |        |            |       |      |
   | Congestion      | R         | R      | R          | NA    | NA   |
   | Status          |           |        |            |       |      |
   +------------------------------------------------------------------+
   | User Part       | R         | NA     | NA         | R     | R    |
   | Unavailable     |           |        |            |       |      |
   +------------------------------------------------------------------+

      Table 27: Required/Not Applicable Fields for MTPP Operations

4.5.1.3 Socket Option Registration Primitive (sorp)

   The 'sorp' primitive allows IP nodes to set various options on a
   socket by socket basis.  This allows the IP node some control over
   the communication that will occur across the TALI connection.  The
   'sorp' primitives allows this socket option control to be transferred
   in-band, via TALI messages, to the IP nodes.

   The SORP primitives capabilities that are available to the IP device
   in SG are as follows:






Sprague, et al.              Informational                     [Page 88]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   *  Set SORP Flags: Used to set the flags bit field.  The receiver of
      this message should store the bit settings indicated in the SORP
      Flag field.

   *  Request Current SORP Flags Settings: Used to poll for the status
      of the bit field options.  The receiver of this message should
      send a Reply w/ Current SORP Flag settings.

   *  Reply w/ Current SORP Flag Settings: Used to reply to a poll,
      indicating the current bit field settings to the far end.

   As of TALI 2.0, each socket option is stored as a bit in a 32 bit
   bit-field.  Each bit in the field indicates the setting for 1 option.
   A bit field with a 0 value indicates the option is DISABLED.  A bit
   field with a 1 value indicates the option is ENABLED.  The following
   options are currently supported:

   *  ENABLE/DISABLE BROADCAST PHASE MTPP PRIMITIVES: Traditional STPs
      send Broadcast Phase TFPs and TFAs to all adjacent nodes when the
      point code availability changes for destinations in the STP's SS7
      routing table.  These Broadcast Phase TFA/TFP SS7 messages are
      converted into TALI mtpp primitives by SG nodes such as the SG.
      The ENABLE/DISABLE BROADCAST PHASE MTPP PRIMITIVES options allow
      each IP node to tell the remote end whether the IP node wants to
      receive the mtpp primitives that result from SS7 broadcast phase
      messages.

      *  As an implementation note: In the SG, each defined socket has a
         flag, 'enable_broadcast_phase_primitives', which is initialized
         to FALSE each time the socket connects.  The IP node should
         send the ENABLE BROADCAST PHASE MESSAGES operation to the SG to
         announce that it wants to receive unsolicited status changes
         for a particular socket.  As the SG is determining where to
         send broadcast phase TFAs/TFPs, it will interrogate the
         'enable_broadcast_phase_primitives' flag for each socket on
         that socket.

   *  ENABLE/DISABLE RESPONSE METHOD MTPP PRIMITIVES: Traditional STPs
      send Response Method TFPs to adjacent nodes when the adjacent
      nodes continue to send MSUs to the STP that can not be delivered
      (ie: the STP has told the adjacent node that a destination is
      Unavailable, but the adjacent node continues to send traffic
      destined for that unavailable DPC to the STP).  These Response
      Method messages are sent in response to MSUs that are received at
      the STP.  These Response Method TFP messages are converted into
      TALI mtpp primitives by SG nodes such as the SG.  The
      ENABLE/DISABLE RESPONSE METHOD MTPP PRIMITIVES options allow each
      IP node to tell the remote end whether the IP node wants to



Sprague, et al.              Informational                     [Page 89]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


      receive the mtpp primitives that result from SS7 response method
      messages.  In addition to response method TFPs, 2 other SS7
      Network Management messages, namely TFCs (transfer controlled) and
      UPUs (user part unavailable), fall into this RESPONSE METHOD
      grouping.  TFCs and UPUs are similar to response method TFPs due
      to the fact that a previous action by the IP Node (sending traffic
      toward some destination) has caused a response method event back
      to the IP Node.  The primary difference between response method
      TFPs versus response method TFCs/UPUs is that the response method
      TFP is converted to an MTPP primitive and sent back to only the
      original socket, while response method TFCs/UPUs may need to be
      replicated to multiple sockets (after being converted to mtpp
      primitives) since there is no way to tell which socket caused the
      response method event.

      *  As an implementation node: In the SG, each defined socket has a
         flag, 'enable_response_method_primitives', which is initialized
         to FALSE each time the socket connects.  The IP node should
         send the ENABLE RESPONSE METHOD MTPP PRIMITIVES operation to
         the SG to announce that it wants to receive response method
         TFPs when appropriate for a particular socket.  Before the SG
         sends a response method TFP (converted to a mtpp primitive)
         back to an IP node, the SG will interrogate the
         'enable_response_method_primitives' flag for that socket and
         only perform the send if the flag allows it.

   *  ENABLE/DISABLE NORMALIZED SCCP: Version 1.0 of TALI specified that
      the 'sccp' TALI opcode must be used on point to multipoint
      connections in order to transmit SCCP MSUs between the SG and IP
      nodes.  When using the 'sccp' opcode, the MTP3 header portion of
      the original SS7 MSU was stripped from the MSU and was NOT part of
      the data transmitted across the TALI connection.  The sender of
      the 'sccp' TALI message was responsible for duplicating the
      DPC/OPC fields from the MTP3 header into appropriate fields in the
      SCCP portion of the message (into the Called/Calling Party Address
      Pt Code fields) before sending as a 'sccp' opcode.  This option
      provides a way to send SCCP MSUs across TALI point to multipoint
      connections that includes the MTP3 header as part of the data
      transmitted, and does NOT involve any modification to the original
      SS7 SCCP MSU.  When the ENABLE NORMALIZED SCCP primitive is
      received, SCCP MSUs should be sent across the TALI interface using
      the 'mtp3' opcode.  This transmission should include the entire
      MTP3 header + the sccp portion of the original MSU.  No
      modification of the original SS7 MSU should occur.  When the
      DISABLE NORMALIZED SCCP primitive is received, SCCP MSUs should be
      sent across the TALI interface using the 'sccp' opcode as
      specified in version 1.0 of TALI.




Sprague, et al.              Informational                     [Page 90]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   *  ENABLE/DISABLE NORMALIZED ISUP: Version 1.0 of TALI specified that
      the 'isot' TALI opcode must be used on point to multipoint
      connections in order to transmit ISUP MSUs between the SG and IP
      nodes.  When using the 'isot' opcode, the original SS7 MSU,
      including the MTP3 header portion, was transmitted in a 'isot'
      TALI message.  This option indicates that the far end would prefer
      to receive ISUP MSUs using the 'mtp3' TALI opcode as opposed to
      the 'isot' opcode.  When the option is ENABLED, the 'mtp3' opcode
      is used to transmit ISUP MSUs, including the MTP3 header, across
      the TALI connection.  When the option is DISABLED, the 'isot'
      opcode is used as in TALI Release 1.0.

   The data structure used for 'sorp' messages is as presented in the
   next table.  The data structure below should begin at byte 14 of the
   TALI message as shown in Table 12.




































Sprague, et al.              Informational                     [Page 91]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   +------------------------------------------------------------------+
   | Octets | Field Name  | Description                  | Field Type |
   +------------------------------------------------------------------+
   | 2      | SORP        | Identifies which 'sorp'      | Integer    |
   |        | Operation   | operation/capability is      |            |
   |        |             | provided in this message.    |            |
   |        |             | This integer field uses the  |            |
   |        |             | following encodings:         |            |
   |        |             | 0x0001 = Set SORP Flags      |            |
   |        |             | 0x0002 = Request Current     |            |
   |        |             |          SORP Flags Settings |            |
   |        |             | 0x0003 = Reply w/ Current    |            |
   |        |             |          SORP Flag Settings  |            |
   +------------------------------------------------------------------+
   | 2      | SORP Flags  | A 4 byte bit-field that uses | Bit-Field  |
   |        |             | each bit as an enabled/      |            |
   |        |             | disabled flag for a          |            |
   |        |             | particular socket option.    |            |
   |        |             | Bit x = 0 indicates the      |            |
   |        |             |         option is DISABLED.  |            |
   |        |             | Bit x = 1 indicates the      |            |
   |        |             |         option is ENABLED.   |            |
   |        |             | The assignments for each BIT |            |
   |        |             | are as follows:              |            |
   |        |             | Bit 0 = Broadcast Phase MTPP |            |
   |        |             |         Primitives           |            |
   |        |             | Bit 1 = Response Method MTPP |            |
   |        |             |         Primitives           |            |
   |        |             | Bit 2 = Normalized SCCP      |            |
   |        |             | Bit 3 = Normalized ISUP      |            |
   +------------------------------------------------------------------+

     Table 28: Message Data Structure to be used for 'sorp' Primitive

4.5.2 Extended Service Message (xsrv)

   The Extended Service, 'xsrv', opcode is added to the TALI 2.0
   protocol to lay the groundwork for providing a means to transport
   other types of service traffic (beyond 'sccp', 'isot', 'mtp3', and
   'saal') in future revisions of this protocol without having to define
   a new opcode as each new service type is identified and added.  The
   PRIMITIVE field will uniquely identify each new service type as they
   are added.  It is envisioned that some 'xsrv' messages can be
   received and processed in any of the TALI NEx-FEx state, while some
   other 'xsrv' messages can only be received and processed in the NEA-
   FEA state (such as Service data in version 1.0 of TALI).





Sprague, et al.              Informational                     [Page 92]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   There are no specific PRIMITIVES defined for this opcode in this
   release.  It is expected that some new service messages will be added
   in the future.  This opcode provides for grouping of the new service
   data types.

   +------------------------------------------------------------------+
   | Octets | Field Name  | Description                               |
   +------------------------------------------------------------------+
   | 0..3   | SYNC        | 'TALI'                                    |
   +------------------------------------------------------------------+
   | 4..7   | OPCODE      | 'xsrv'                                    |
   +------------------------------------------------------------------+
   | 8..9   | LENGTH      | Length                                    |
   +------------------------------------------------------------------+
   | 10..13 | Primitive   | To be determined                          |
   +------------------------------------------------------------------+
   | 14..   | Message     | To be determined                          |
   |   2000 | Data        |                                           |
   +------------------------------------------------------------------+

4.5.3 Special Message (spcl)

   The Special Message, 'spcl', opcode is added to the TALI 2.0 protocol
   to provide a way for vendors to build special services into their
   TALI implementations that are only activated when the implementation
   is connected to other equipment implementing the same special
   services.  'spcl' messages can be received and processed in any of
   the TALI NEx-FEx states.  This opcode is intended to provide a
   general means to discover more information regarding who the TALI
   session is connected to, and to provide means to enable special
   features based on the vendor/implementation on the far end.

   As part of the 2.0 specification, 4 primitives are initially defined
   for this opcode:

   *  'smns' - Special Messages Not Supported.
   *  'qury' - Query.
   *  'rply' - Reply.
   *  'usim' - UnSolicited Information Message.

   Additional primitives can be added in future versions of the TALI
   protocol.









Sprague, et al.              Informational                     [Page 93]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   +------------------------------------------------------------------+
   | Octets | Field Name  | Description                               |
   +------------------------------------------------------------------+
   | 0..3   | SYNC        | 'TALI'                                    |
   +------------------------------------------------------------------+
   | 4..7   | OPCODE      | 'spcl'                                    |
   +------------------------------------------------------------------+
   | 8..9   | LENGTH      | Length                                    |
   +------------------------------------------------------------------+
   | 10..13 | Primitive   | 'smns' - special messages not supported   |
   |        |             | 'qury' - query                            |
   |        |             | 'rply' - reply                            |
   |        |             | 'usim' - UIM (unsolicited information msg)|
   +------------------------------------------------------------------+
   | 14..X  | Data        | Vendor dependent                          |
   +------------------------------------------------------------------+

4.5.3.1 Special Messages Not Supported (smns)

   This message is sent as a response to a 'spcl' message with a 'qury'
   PRIMITIVE.  A node may send out this message when it wants the Far
   End to know that it does not support 'spcl' messages and wishes not
   to receive them in the future.

   +------------------------------------------------------------------+
   | Octets | Field Name  | Description                               |
   +------------------------------------------------------------------+
   | 0..3   | SYNC        | 'TALI'                                    |
   +------------------------------------------------------------------+
   | 4..7   | OPCODE      | 'spcl'                                    |
   +------------------------------------------------------------------+
   | 8..9   | LENGTH      | Length                                    |
   +------------------------------------------------------------------+
   | 10..13 | Primitive   | 'smns'                                    |
   +------------------------------------------------------------------+

4.5.3.2 Query Message (qury)

   This message can be sent to Query the far end of the connection (ie:
   try to find out more information about the VENDOR, TALI version, or
   other features).  It is expected that each 2.0 implementation would
   respond to a 'qury' with a 'rply'.









Sprague, et al.              Informational                     [Page 94]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   +------------------------------------------------------------------+
   | Octets | Field Name  | Description                               |
   +------------------------------------------------------------------+
   | 0..3   | SYNC        | 'TALI'                                    |
   +------------------------------------------------------------------+
   | 4..7   | OPCODE      | 'spcl'                                    |
   +------------------------------------------------------------------+
   | 8..9   | LENGTH      | Length                                    |
   +------------------------------------------------------------------+
   | 10..13 | Primitive   | 'qury'                                    |
   +------------------------------------------------------------------+

4.5.3.3 Reply Message (rply)

   The 'rply' message provides a way for a TALI 2.0 implementation to
   identify itself in more detail.  The information included in the
   reply includes:

   *  PEC - a 2 byte field that identifies the vendor for the TALI
      implemenation.

   *  Version Number - a 12 byte field that identifies the TALI version
      of the implementation.

   *  Other Vendor Specific Data - the format of any remaining data that
      a particular vendor wants to provide is specific to each vendor.

   +------------------------------------------------------------------+
   | Octets | Field Name  | Description                               |
   +------------------------------------------------------------------+
   | 0..3   | SYNC        | 'TALI'                                    |
   +------------------------------------------------------------------+
   | 4..7   | OPCODE      | 'spcl'                                    |
   +------------------------------------------------------------------+
   | 8..9   | LENGTH      | Length                                    |
   +------------------------------------------------------------------+
   | 10..13 | Primitive   | 'rply'                                    |
   +------------------------------------------------------------------+
   | 14..15 | PEC         | Private Enterprise Code *                 |
   |        |             | (Vendor ID Number, Integer Field)         |
   +------------------------------------------------------------------+
   | 16..27 | Version     | 'vers xxx.yyy'                            |
   |        | Label       |                                           |
   +------------------------------------------------------------------+
   | 28..?  | Other Vendor| Free Format data area, specific to each   |
   |        | Specific    | vendor                                    |
   |        | Data        |                                           |
   +------------------------------------------------------------------+



Sprague, et al.              Informational                     [Page 95]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   *See Table 4 for details on the PEC field.

4.5.3.4 Unsolicited Information Message (USIM)

   A 'usim' provides the same information as the 'rply' primitive.  The
   'usim' can be sent at any time by a 2.0 implementation (whereas the
   'rply' should only be sent in reply to a 'qury').

   +------------------------------------------------------------------+
   | Octets | Field Name  | Description                               |
   +------------------------------------------------------------------+
   | 0..3   | SYNC        | 'TALI'                                    |
   +------------------------------------------------------------------+
   | 4..7   | OPCODE      | 'spcl'                                    |
   +------------------------------------------------------------------+
   | 8..9   | LENGTH      | Length                                    |
   +------------------------------------------------------------------+
   | 10..13 | Primitive   | 'usim'                                    |
   +------------------------------------------------------------------+
   | 14..15 | PEC         | Private Enterprise Code *                 |
   |        |             | (Vendor ID Number, Integer Field)         |
   +------------------------------------------------------------------+
   | 16..27 | Version     | 'vers xxx.yyy'                            |
   |        | Label       |                                           |
   +------------------------------------------------------------------+
   | 28..?  | Other Vendor| Free Format data area, specific to each   |
   |        | Specific    | vendor                                    |
   |        | Data        |                                           |
   +------------------------------------------------------------------+

4.6 TALI Timers

   Version 2.0 of the TALI specification does not introduce any new
   timers.  The T1-T4 timers defined previously remain in effect.

   While, it is expected that most implementations wishing to identify
   themselves as 2.0 (or later) would use a non-zero value for T4 - this
   is a not a hard requirement.  The only requirement for identifying
   yourself as 2.0 is to send at least 1 'moni' as per the 2.0 format
   upon connection establishment.

4.7 TALI User Events

   Version 2.0 of the TALI specification does not introduce any new user
   events.  The user events defined in Section 3.4 (mgmt open, mgmt
   close, mgmt allow, mgmt proh, connection established, connection
   lost) remain in effect.




Sprague, et al.              Informational                     [Page 96]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


4.8 TALI States

   Version 2.0 of the TALI specification does not introduce any new TALI
   states.  The TALI states defined in Section 3.6 remain in effect.

4.9 TALI Version 2.0 State Machine

   This section provides the state machine that must be followed by each
   TALI 2.0 implementation in order to be compliant with this
   specification.  As mentioned throughout this document, a 2.0
   implementation is based on several small additions to a 1.0
   implementation and each 2.0 implementation must be willing to inter-
   operate in a backwards compatible mode (a 2.0 implementation
   connected to a 1.0 implementation must fall back to 1.0 features
   only).

4.9.1 State Machine Concepts

   Before presenting the actual state machine, several concepts are
   discussed.

4.9.1.1 General Protocol Rules

   A set of general protocol rules was presented in the 1.0
   specification, in section 3.7.1.1; those rules are still applicable
   to 2.0 implementations.  In addition to those earlier rules, the
   following rules are also applicable to 2.0 nodes:

   *  A 2.0 implementation should identify the TALI version it has
      implemented via the 'moni' message

   *  A 2.0 implementation should process any received 'moni' messages,
      attempting to determine the TALI version of the far end.  A 2.0
      implementation must use an internal flag, such as
      'far_end_version', to track the TALI version that the far end of
      the connection has implemented.  The 'far_end_version' flag should
      be initialized to version 1.0.

   *  A 2.0 implementation should reject/ignore internal requests (from
      software layers in it's own product, or requests from the
      management interface for the device) to send TALI messages that
      require 2.0 opcodes when the far end is a 1.0 implementation.  A
      2.0 implementation should only send TALI messages that require new
      2.0 opcodes (mgmt, xsrv, spcl) when it knows the far end is
      capable of processing those opcodes (when 'far_end_version' is 2.0
      or greater).





Sprague, et al.              Informational                     [Page 97]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   *  Upon receiving a TALI message with a 2.0 opcode, a 2.0
      implementation should interrogate its 'far_end_flag'; if the far
      end is not 2.0 or greater, the arrival of the message should be
      treated as a Protocol Violation.  If the far end is 2.0 or
      greater, the message should be processed according to the nodes
      2.0 capabilities, or ignored (if the node has chosen not to
      implement any 2.0 functionalities).

4.9.1.2 Graceful Shutdown of a Socket

   The steps to perform a graceful shutdown of each socket were
   presented in the 1.0 specification, in section 3.7.1.2.  Those steps
   are not changed for 2.0 implementations.

4.9.1.3 TALI Protocol Violations

   Each TALI implementation must detect when violations of the TALI
   protocol have occurred and react accordingly.  Protocol violations
   include:

   *  Invalid sync code in a received message

   *  Invalid opcode in a received message

   *  Invalid length field in a received message

   *  Not receiving an 'allo' or 'proh', in response to the origination
      of a 'test' , before the T2 timer expires

   *  Receiving Service Messages on a prohibited socket.

   *  TCP Socket errors - Connection Lost

   *  Receiving a TALI message with a 2.0 opcode ('mgmt', 'xsrv', '
      spcl') from a far end that has not identified itself as a 2.0
      implementation.

   In the state machine that follows, State/Event combinations that
   should be treated as protocol violations are indicated via a 'PV' in
   the state/event cell.  All of the 'PV' events are then processed as
   per the 'Protocol Violation' row in the table.

4.9.2 The State Machine

   Internal Data required for State Machine:

   *  boolean sock_allowed.  This flag indicate whether the NE is
      allowed to carry Service Messages.



Sprague, et al.              Informational                     [Page 98]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   *  Far_end_version.  This enumeration should track the TALI version
      of the far end of the socket.

   Initial Conditions:
   sock_allowed = FALSE
   far_end_version = 1.0
   state = OOS
   no timers running

   +------------------------------------------------------------------+
   |   State| OOS  |Connecting| NEP-FEP | NEP-FEA | NEA-FEP | NEA-FEA |
   |Event   |      |          |         |         |         |         |
   +------------------------------------------------------------------+
   |T1 Exp. |      |          |Send test|Send test|Send test|Send test|
   |        |      |          |Start T1 |Start T1 |Start T1 |Start T1 |
   |        |      |          |Start T2 |Start T2 |Start T2 |Start T2 |
   +------------------------------------------------------------------+
   |T2 Exp. |      |          |   PV    |   PV    |   PV    |   PV    |
   +------------------------------------------------------------------+
   |T3 Exp. |      |          |   PV    |   PV    |         |         |
   +------------------------------------------------------------------+
   |T4 Exp. |      |          |Send moni|Send moni|Send moni|Send moni|
   |        |      |          |Start T4 |Start T4 |Start T4 |Start T4 |
   +------------------------------------------------------------------+
   |Rcv test|      |          |Send proh|Send proh|Send allo|Send allo|
   +------------------------------------------------------------------+
   |Rcv allo|      |          | Stop T2 | Stop T2 | Stop T2 | Stop T2 |
   |        |      |          | NEP-FEA |         | NEA-FEA |         |
   +------------------------------------------------------------------+
   |Rcv proh|      |          | Stop T2 | Stop T2 | Stop T2 | Stop T2 |
   |        |      |          |Send proa|Send proa|Send proa|Flush or |
   |        |      |          |         | NEP-FEP |         | reroute |
   |        |      |          |         |         |         |Send proa|
   |        |      |          |         |         |         | NEA-FEP |
   +------------------------------------------------------------------+
   |Rcv proa|      |          | Stop T3 | Stop T3 |         |         |
   +------------------------------------------------------------------+
   |Rcv moni|      |          |Update   |Update   |Update   |Update   |
   |        |      |          |'far end |'far end |'far end |'far end |
   |        |      |          |version' |version' |version' |version' |
   |        |      |          |based on |based on |based on |based on |
   |        |      |          |moni     |moni     |moni     |moni     |
   |        |      |          |Convert  |Convert  |Convert  |Convert  |
   |        |      |          | to mona | to mona | to mona | to mona |
   |        |      |          |Send mona|Send mona|Send mona|Send mona|
   +------------------------------------------------------------------+





Sprague, et al.              Informational                     [Page 99]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   |Rcv mona|      |          |Implemen-|Implemen-|Implemen-|Implemen-|
   |        |      |          |tation   |tation   |tation   |tation   |
   |        |      |          |dependent|dependent|dependent|dependent|
   +------------------------------------------------------------------+
   |Rcv     |      |          |   PV    |If T3 run|   PV    |Process  |
   | Service|      |          |         | Process |         |         |
   |        |      |          |         |Else PV  |         |         |
   +------------------------------------------------------------------+
   |Rcv mgmt|      |          |If FE<   |If FE<   |If FE<   |If FE<   |
   |        |      |          | 2.0 PV  | 2.0 PV  | 2.0 PV  | 2.0 PV  |
   |        |      |          |Else     |Else     |Else     |Else     |
   |        |      |          | Process | Process | Process | Process |
   +------------------------------------------------------------------+
   |Rcv xsrv|      |          |If FE<   |If FE<   |If FE<   |If FE<   |
   |        |      |          | 2.0 PV  | 2.0 PV  | 2.0 PV  | 2.0 PV  |
   |        |      |          |Else     |Else     |Else     |Else     |
   |        |      |          | Process | Process | Process | Process |
   +------------------------------------------------------------------+
   |Rcv spcl|      |          |If FE<   |If FE<   |If FE<   |If FE<   |
   |        |      |          | 2.0 PV  | 2.0 PV  | 2.0 PV  | 2.0 PV  |
   |        |      |          |Else     |Else     |Else     |Else     |
   |        |      |          | Process | Process | Process | Process |
   +------------------------------------------------------------------+
   |Connect.|      | Start T1 |         |         |         |         |
   |Estab.  |      | Start T2 |         |         |         |         |
   |        |      | Start T4 |         |         |         |         |
   |        |      |(if non-0)|         |         |         |         |
   |        |      |if sock_  |         |         |         |         |
   |        |      |  allowed |         |         |         |         |
   |        |      |  = TRUE  |         |         |         |         |
   |        |      | send allo|         |         |         |         |
   |        |      | send test|         |         |         |         |
   |        |      | NEA-FEP  |         |         |         |         |
   |        |      |else      |         |         |         |         |
   |        |      | send proh|         |         |         |         |
   |        |      | send test|         |         |         |         |
   |        |      | NEP-FEP  |         |         |         |         |
   +------------------------------------------------------------------+
   |Connect.|      |          |   PV    |   PV    |   PV    |   PV    |
   |Lost    |      |          |         |         |         |         |
   +------------------------------------------------------------------+
   |Protocol|      |          |Stop all |Stop all |Stop all |Stop all |
   |Violat. |      |          | timers  | timers  | timers  | timers  |
   |        |      |          |Close the|Close the|Close the|Close the|
   |        |      |          | socket  | socket  | socket  | socket  |
   |        |      |          |Connect- |Connect- |Connect- |Connect- |
   |        |      |          |  ing    |  ing    |  ing    |  ing    |
   +------------------------------------------------------------------+



Sprague, et al.              Informational                    [Page 100]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   |Mgmt.   |Open  |          |         |         |         |         |
   |Open    |socket|          |         |         |         |         |
   |Socket  |Conne-|          |         |         |         |         |
   |        | cting|          |         |         |         |         |
   +------------------------------------------------------------------+
   |Mgmt.   |      |Close the |Stop all |Stop all |Stop all |Stop all |
   |Close   |      | socket   | timers  | timers  | timers  | timers  |
   |Socket  |      |OOS       |Close the|Close the|Close the|Close the|
   |        |      |          | socket  | socket  | socket  | socket  |
   |        |      |          |OOS      |OOS      |OOS      |OOS      |
   +------------------------------------------------------------------+
   |Mgmt.   |sock_ |sock_allo-|sock_all-|sock_all-|sock_all-|sock_all-|
   |Prohibit|allow-| wed=FALSE| owed=   | owed=   | owed=   | owed=   |
   |Socket  |ed =  |          | FALSE   | FALSE   | FALSE   | FALSE   |
   |        |FALSE |          |         |         |send proh|send proh|
   |        |      |          |         |         |start t3 |start t3 |
   |        |      |          |         |         | NEP-FEP | NEP-FEA |
   |        |      |          |         |         |         |         |
   +------------------------------------------------------------------+
   |Mgmt.   |sock_ |sock_allo-|sock_all-|sock_all-|sock_all-|sock_all-|
   |Allow   |allow-| wed=TRUE | owed=   | owed=   | owed=   | owed=   |
   |Traffic |ed =  |          | TRUE    | FALSE   | TRUE    | TRUE    |
   |        |TRUE  |          |send allo|send allo|         |         |
   |        |      |          | NEA-FEP | NEA-FEA |         |         |
   +------------------------------------------------------------------+
   |User    |reject| reject   | reject  | reject  | reject  | send    |
   |Part    |data  | data     | data    | data    | data    | data    |
   |Msgs.   |      |          |         |         |         |         |
   +------------------------------------------------------------------+
   |Request |      |          |If FE<2.0|If FE<2.0|If FE<2.0|If FE<2.0|
   |to Tx   |      |          | Ignore  | Ignore  | Ignore  | Ignore  |
   |mgmt    |      |          |Else     |Else     |Else     |Else     |
   |        |      |          | Process | Process | Process | Process |
   +------------------------------------------------------------------+
   |Request |      |          |If FE<2.0|If FE<2.0|If FE<2.0|If FE<2.0|
   |to Tx   |      |          | Ignore  | Ignore  | Ignore  | Ignore  |
   |xsrv    |      |          |Else     |Else     |Else     |Else     |
   |        |      |          | Process | Process | Process | Process |
   +------------------------------------------------------------------+
   |Request |      |          |If FE<2.0|If FE<2.0|If FE<2.0|If FE<2.0|
   |to Tx   |      |          | Ignore  | Ignore  | Ignore  | Ignore  |
   |spcl    |      |          |Else     |Else     |Else     |Else     |
   |        |      |          | Process | Process | Process | Process |
   +------------------------------------------------------------------+

                   Table 29: TALI 2.0 State Machine





Sprague, et al.              Informational                    [Page 101]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


4.10 TALI 2.0 Specification Limitations

   Several limitations with the TALI 2.0 specification are identified.
   These are considered possible areas for expansion of the protocol in
   the future:

   *  Support for different types of routing keys is limited.  It is
      envisioned that new routing key types will need to be added and
      supported as new applications are identified.

   *  An opcode, or new primitive within an existing opcode, could be
      added as a means of returning unknown or unsupported data to the
      sender.  In addition to discarding and storing internal debug
      data, an implementation may want to return the original TALI
      message to the sender when the receiver of the message deems the
      message to be unknown, unsupported, or incorrectly formatted.

5. Success/Failure Codes

   The following list provides all the known success/failure codes that
   are being used for the rkrp feature.  New defines will be added to
   the end of the list as they are identified.

   Error #    Meaning
   1          Transaction successfully completed.
   2          Length of TALI msg is insufficient to contain all
              required information for rkrp operation
   3          Unsupported 'rkrp' operation
   4          Invalid SI.  SI must be in range 0..15
   5          Invalid SI/operation combination.  Split and resize only
              supported for SI=4,5,13.  Enter, delete and override
              supported for all SI.
   6          Invalid DPC.  Point code cannot be zero, and must be full
              point code.
   7          Invalid SSN.  SSN must be in range 0..255.
   8          Invalid OPC.  Point code cannot be zero, and must be full
              point code.
   9          Invalid CICS.  Must be in range appropriate for SI and PC
              type.
   10         Invalid CICE.  Must be in range appropriate for SI and PC
              type.
   11         Invalid CIC range.  CICS must be less than or equal to
              CICE.  On a split operation, CICS must be strictly less
              than than CICE (cannot split an range with only one
              entry).
   12         Invalid NCICS.  Must be in range appropriate for SI and
              PC type.




Sprague, et al.              Informational                    [Page 102]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   13         Invalid NCICE.  Must be in range appropriate for SI and
              PC type.
   14         Invalid new CIC range.  NCICS must be less than or equal
              to NCICE.
   15         Invalid SPLIT value.   Must be in range appropriate for
              SI and PC type.  Must be greater than CICS and less than
              or equal to CICE.
   16         No free entries in table.
   17         CIC range overlaps but does not match existing entry.
   18         Entry already has 16 associations.
   19         Entry to be changed not found in table.
   20         New entry would overlap another entry (allowed to overlap
              the entry being changed, but no others).
   21         Entry to be deleted not found in table.
   22         TUP routing keys are not supported for ANSI networks

6. Security Considerations

   TALI is an interface for the transport of SS7 traffic and management
   messages across an IP network.  As with traditional PSTN networks,
   the IP networks using TALI are expected to well engineered systems.
   The use of virtual private networks and firewalls is to be expected.
   In addition, the use of IPSEC will bring added security benefit to
   the network.

7. References

   [1]  Bell Communications Research, Specification of Signaling System
        Number 7, GT-246-CORE, Bellcore, Issue 1, December 1994.

   [2]  Postel, J., "Internet Protocol", STD 5, RFC 791, September 1981.

   [3]  Postel, J., "Internet Control Message Protocol", STD 5, RFC 792,
        September 1981.

   [4]  Postel, J., "Transmission Control Protocol", STD 7, RFC 793,
        September 1981.

   [5]  Logical Link Control, IEEE 802.2 and ISO 8802.2

   [6]  Carrier Sense Multiple Access with Collision Detection
        (Ethernet), IEEE 802.3 and ISO 8802-3 CSMA/CD.

   [7]  Virtual LAN, IEEE 802.1 Q and ISO 8802-1Q CSMA/CD.

   [8]  Bell Communications Research, Generic Requirements for CCS Nodes
        Supporting ATM High-Speed Signaling Links (HSLs), GR-2878-CORE,
        Issue 1, Bellcore, November 1995.



Sprague, et al.              Informational                    [Page 103]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


   [9]  Bell Communications Research, Asynchronous Transfer Mode (ATM)
        and ATM Adaptation Layer (AAL) Protocols, GR-1113-CORE,
        Bellcore.

   [10] American National Standards Institute, B-ISDN Signaling ATM
        Adaptation Layer - Service Specific Connection Oriented Protocol
        (SSCOP), T1.637.

   [11] American National Standards Institute, B-ISDN Signaling ATM
        Adaptation Layer - Service Specific Coordination Function for
        Support of Signaling at the Network Node Interface (SSCF at the
        NNI), T1.645.

   [12] American National Standards Institute, B-ISDN Signaling ATM
        Adaptation Layer - Layer Management for the SAAL at the NNI,
        T1.652.

8. Acknowledgments

   The authors would like to thank Ken Morneault for his comments and
   contributions to the document.






























Sprague, et al.              Informational                    [Page 104]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


9. Authors' Addresses

   David Sprague
   Tekelec
   5200 Paramount Pkwy.
   Morrisville, NC  27560
   Phone: +1 919-460-5563
   EMail: david.sprague@tekelec.com


   Dan Brendes
   Tekelec
   5200 Paramount Pkwy.
   Morrisville, NC  27560
   Phone: +1 919-460-2162
   EMail: dan.brendes@tekelec.com


   Robby Benedyk
   Tekelec
   5200 Paramount Pkwy.
   Morrisville, NC  27560
   Phone: +1 919-460-5533
   EMail: robby.benedyk@tekelec.com


   Joe Keller
   Tekelec
   5200 Paramount Pkwy.
   Morrisville, NC  27560
   Phone: +1 919-460-5549
   EMail: joe.keller@tekelec.com



















Sprague, et al.              Informational                    [Page 105]


RFC 3094      Tekelec's Transport Adapter Layer Interface     April 2001


Full Copyright Statement

   Copyright (C) The Internet Society (2001).  All Rights Reserved.

   This document and translations of it may be copied and furnished to
   others, and derivative works that comment on or otherwise explain it
   or assist in its implementation may be prepared, copied, published
   and distributed, in whole or in part, without restriction of any
   kind, provided that the above copyright notice and this paragraph are
   included on all such copies and derivative works.  However, this
   document itself may not be modified in any way, such as by removing
   the copyright notice or references to the Internet Society or other
   Internet organizations, except as needed for the purpose of
   developing Internet standards in which case the procedures for
   copyrights defined in the Internet Standards process must be
   followed, or as required to translate it into languages other than
   English.

   The limited permissions granted above are perpetual and will not be
   revoked by the Internet Society or its successors or assigns.

   This document and the information contained herein is provided on an
   "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
   TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
   BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
   HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
   MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Acknowledgement

   Funding for the RFC Editor function is currently provided by the
   Internet Society.



















Sprague, et al.              Informational                    [Page 106]